Engine Oil Pump - Remove and Install
开始:
- 拆卸前壳体。
注: 参考技术规格, "发动机设计",了解非指定的发动机扭矩值。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 拆下螺钉 (2) 和盖 (1)。
Show/hide table
图 2 g02788689 - 将内转子 (4) 从外转子 (3) 上拆下。
Show/hide table
图 1 | g02788686 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 129-1967 | 白色润滑脂 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
如果发动机机油泵的任何零件磨损或损坏,必须更换整个发动机机油泵组件。 |
- 确保发动机机油泵的所有部件清洁、无磨损或损坏。
- 参阅技术规格, "发动机机油泵",了解所有发动机机油泵允许间隙。
Show/hide table
图 3 g02788689 - 将外转子 (3) 定位到泵体中。 检查外转子 (3) 和泵体之间的间隙。
- 将内转子 (4) 装入外转子 (3) 中。 检查外转子 (3) 和内转子 (4) 的凸轮之间的间隙。
Show/hide table
图 4 g02788686 - 使用工具 (A) 将一条塑料线间隙规定位到外转子表面。 定位盖 (1),然后安装螺钉 (2) 并拧紧。 拆下盖 (1) 并检查转子和盖 (1) 之间的间隙。
- 安置盖 (1) 并安装螺钉 (2)。 拧紧螺钉 (2) 至扭矩为
8 to 9 N·m (70 to 83 lb in) 。
结束:
- 安装前壳体。
Caterpillar Information System:
C3.3B Engines for Caterpillar Built Machines Water Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.3B Engines for Caterpillar Built Machines Flywheel - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Remove - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Install - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C3.3B Engines for Caterpillar Built Machines Idler Gear - Remove and Install
HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000} HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000}
C3.3B Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C3.3B Engines for Caterpillar Built Machines Bridge Dowels - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
2013/01/21 New Software is Available for Certain 3512C Petroleum Engines {1901, 1920}
C32 Auxiliary Engine Belts - Inspect/Adjust/Replace
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000} Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
2013/03/29 New Engine Oil Hoses Are Used on Certain Excavators Equipped with C13 Engines {1308}
Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078} Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078}
C32 Marine Generator Set Control Panel - Marine Generator Set Engine Control Panel 3 (MGECP 3)
C3.3B Engines for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install