Housing (Front) - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Three Bond 1217H | 1 |
开始:
- 拆下曲轴前密封。
注: 参考技术规格, "发动机设计",了解非指定的发动机扭矩值。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。
Show/hide table
图 1 g02795275 - 将软管组件 (1) 和 (2) 从机油冷却器上断开。
Show/hide table
图 2 g02795251 - 拆下螺栓 (4)。
- 拆下前壳体 (3) 和密封垫。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保前壳体清洁且无损坏。 如有必要,更换前壳体。
- 清洁缸体的所有密封垫表面。
Show/hide table
图 3 g02864317 - 在下曲轴箱部分 (6) 和上曲轴箱部分 (5) 之间的接缝处涂覆工具 A。
Show/hide table
图 4 g02795251 - 对准新密封垫,然后将密封垫安装到缸体上。
- 按照从一侧到另一侧的顺序拧紧 13 个螺栓 (4)。 拧紧螺栓 (4) 至扭矩为
24 to 27 N·m (212 to 239 lb in) Show/hide table图 5 g02795275 - 将软管组件 (1) 和 (2) 连接到机油冷却器上。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
结束:
- 安装曲轴前油封。
Caterpillar Information System:
C3.3B Engines for Caterpillar Built Machines Bridge Dowels - Remove and Install
C1.5 and C2.2 Engines for Caterpillar Built Machines Diesel Particulate Filter - Clean
2014/05/30 Improved Camshafts Are Now Used on Certain C27 and C32 Machines {1210}
2014/05/30 An Improved Rocker Arm Assembly Is Used on C27 and C32 Machine Engines {1102, 1123}
PM3516 Power Modules Belts - Inspect/Adjust/Replace
C9.3 Tier 4 Final Engines Component Location
C3.3B Engines for Caterpillar Built Machines Rocker Shaft and Push Rod - Remove and Install
C3.3B Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C3.3B Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C3.3B Engines for Caterpillar Built Machines Camshaft and Valve Lifters - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000} HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000}
C3.3B Engines for Caterpillar Built Machines Idler Gear - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C3.3B Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Install - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Remove - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Flywheel - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install