Engine Oil Cooler - Remove and Install
注: 请参阅技术规格 UENR3421 "发动机设计",了解非指定的发动机扭矩值。
- 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
Show/hide table
图 1 g02788218 - 将发动机机油滤清器 (3) 从发动机机油冷却器 (1) 上拆下。
- 断开软管组件 (2) 和 (4)。
Show/hide table
图 2 g02788221 - 拆下中间双头螺柱 (5),然后从定位器上拆下发动机机油冷却器 (1)。
- 将 O 形密封圈从发动机机油冷却器 (1) 上拆下。
- 按与拆卸相反的顺序安装机油冷却器 (1)。
- 安装 O 形密封圈。 将发动机机油冷却器 (1) 定位到前壳体上的定位器上。 安装中间双头螺柱 (5)。 拧紧中间双头螺柱 (5) 至扭矩为
40 to 44 N·m (29 to 33 lb ft) 。
- 安装 O 形密封圈。 将发动机机油冷却器 (1) 定位到前壳体上的定位器上。 安装中间双头螺柱 (5)。 拧紧中间双头螺柱 (5) 至扭矩为
Caterpillar Information System:
C3.3B Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.3B Engines for Caterpillar Built Machines Flywheel - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Remove - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Install - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C3.3B Engines for Caterpillar Built Machines Idler Gear - Remove and Install
HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000} HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000}
C3.3B Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
2013/01/21 New Software is Available for Certain 3512C Petroleum Engines {1901, 1920}
C32 Auxiliary Engine Belts - Inspect/Adjust/Replace
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000} Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
2013/03/29 New Engine Oil Hoses Are Used on Certain Excavators Equipped with C13 Engines {1308}
Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078} Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078}
C32 Marine Generator Set Control Panel - Marine Generator Set Engine Control Panel 3 (MGECP 3)
C3.3B Engines for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install