Crankshaft Rear Seal - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| e | 1U-7598 | 密封安装工具总成 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 替代后密封随耐磨套一起提供。 此耐磨套必须与后密封一起安装。 新出厂的发动机没有耐磨套。 如果以下情况存在，严禁安装后密封：
- 曲轴后密封已经和耐磨套分离。
- 后密封总成出现损坏迹象。
- 曲轴后密封已经过润滑。 此油封的设计在安装时必须干躁。
- 安装曲轴后密封前，确保曲轴后侧清洁干燥。
- 利用工具 (E) 安装曲轴后密封 (1) 。
Show/hide table
 | |
| 图 1 | g01026625 |
典型实例 | |
End By: 安装飞轮。 参考 拆解和组装, "飞轮 - 拆卸和安装"。
Caterpillar Information System:
C7 PETROLEUM Petroleum Engine Water Temperature Regulator - Remove and Install
C175-16 and C175-20 Generator Set Engines Cylinder Head Valves
345D, 349D and 349D2 Excavator Machine System Specifications Hydraulic Oil Cooler Lines Group
345D, 349D and 349D2 Excavator Machine System Specifications Swing Motor Lines
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
C7 PETROLEUM Petroleum Engine Engine Oil Pump - Assemble
Identification of Non-Metallic Discs that are Used in Power Shift Transmissions {3030, 3155} Identification of Non-Metallic Discs that are Used in Power Shift Transmissions {3030, 3155}
C175-16 and C175-20 Generator Set Engines Inlet Air Temperature Is High
C175-16 and C175-20 Generator Set Engines Exhaust Temperature Is Low
345D, 349D and 349D2 Excavators Hydraulic System Boom Drift Reduction Valve
2008/05/01 Improvements have been made to Remanufactured Fuel Injectors {1251, 1254, 1290, 1713}
2008/04/07 Improvements have been made to Remanufactured Fuel Injectors {1251, 1254, 1290, 1713}
2008/03/17 A New Bearing Block within the Governor is Now Used {1000}
C4.4 and C6.6 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C7 PETROLEUM Petroleum Engine Housing (Front) - Remove
C7 PETROLEUM Petroleum Engine Housing (Front) - Install
2008/04/14 Increased Support for Repair Parts is Available for Products that are sold by Dealer Service Tools from Advanced Technology Services {0599}
2008/03/17 Updated Instruction For The Bypass Harness {0785, 1408}
Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190} Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190}
C7 PETROLEUM Petroleum Engine Valve Mechanism Cover - Remove and Install
Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510} Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510}
345D, 349D and 349D2 Excavator Machine System Specifications Main Hydraulic Pump Mounting