Parking Brake - Remove and Install
Start By:
- Remove the drive shaft. Refer to Disassembly and Assembly, "Drive Shaft - Remove and Install" for the correct procedure.
- Disengage the parking brake.
Show/hide table
Illustration 1 g00663592 - Remove bolt (1) and remove retainer (2).
Show/hide table
Illustration 2 g00663600 - Remove brake drum (3).
Show/hide table
Illustration 3 g00891200 - Remove bolts (5).
- Remove brake assembly (6). When you remove brake assembly (6), lever assembly (4) will fall.
Show/hide table
Illustration 4 g00891201 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Remove springs (6) and separate brake assembly (7).
- Assemble parking brake (7) and install springs (6).
Show/hide table
Illustration 6 g00891200 - Install lever assembly (4) and install brake assembly (6).
- Install bolts (5). Tighten bolts (5) to
120 ± 20 N·m (89 ± 15 lb ft) .Show/hide tableIllustration 7 g00663600 - Install brake drum (3).
Show/hide table
Illustration 8 g00663592 - Install retainer (2) and install bolt (1). Tighten bolt (1) to
120 ± 20 N·m (89 ± 15 lb ft) . - Adjust the parking brake. Refer to Testing and Adjusting, "Parking Brake Control - Adjust" for the correct procedure.
Show/hide table
Illustration 5 | g00891201 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
End By:
- Install the drive shaft. Refer to Disassembly and Assembly, "Drive Shaft - Remove and Install" for the correct procedure.
Caterpillar Information System:
Challenger 65C, Challenger 65D, Challenger 65E, Challenger 70C, Challenger 75C, Challenger 75D, Challenger 75E, Challenger 85C, Challenger 85D, Challenger 85E and Challenger 95E Agricultural Tractors Machine Monitor System Switches
966G Wheel Loader and 972G Wheel Loader Power Train Fill Time for the Transmission Clutch - Calibrate
2000/01/03 Torque Increased for Nuts on Injector Wiring Harness {1290}
TH62, TH63, TH82 and TH83 Telehandlers Braking System Parking Brake
TH62, TH63, TH82 and TH83 Telehandlers Braking System Parking Brake Control Cable - Adjust
D350E Series II, D400E Series II and D400E Series II Ejector Articulated Trucks Braking System General Information
2000/01/03 New Fan Drive Group Includes Serviceable Magnet And Pinned Bearing Races {1359}
2000/02/07 The In-line Refrigerant Dryer Is Improved And A New Dryer For Service Replacement Is Available {7320, 7322}
924G and 924GZ Wheel Loaders Machine Systems Ride Control Accumulator - Remove and Install
CB-535B Vibratory Compactor Cooling System Coolant (DEAC) - Change
CB-535B Vibratory Compactor Circuit Breakers - Reset
539 Knuckleboom Loader Sound Information and Vibration Information
D350E Series II, D400E Series II and D400E Series II Ejector Articulated Trucks Braking System Piston Pump (Brake)
1999/12/20 Change to Tightening Procedure for Cylinder Head Bolts in Disassembly and Assembly, RENR1223 and Disassembly and Assembly, SENR5184 {1100}
CB-535B Vibratory Compactor Cooling System Coolant (ELC) - Change
966G Wheel Loader and 972G Wheel Loader Power Train Secondary Steering - Program
2000/02/14 Thread Lock Compound is Now Used on the Chain Tension Adjuster {6327}
966G Wheel Loader and 972G Wheel Loader Power Train Ride Control Configuration - Program
CB-535B Vibratory Compactor Cooling System Coolant Additive (DEAC) - Add
CB-535B Vibratory Compactor Cooling System Coolant Extender (ELC) - Add
CP-433C, CS-431C and CS-433C Paving Compactors Fuel System - Prime
3408E and 3412E Industrial Engines Engine Speed/Timing Sensor - Calibrate
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0009 - FMI 05 Injector Cylinder 9 open circuit
3054B Industrial Engine Engine Oil Pump - Install