Refill Capacities
发动机润滑系统的容量包括工厂安装的机油滤清器的容量。 辅助机油滤清器系统（如有配备）需要更多的机油。 参考由辅助机油滤清器系统 OEM 提供的技术规格。
Show/hide table
| C175-16 发动机机油加注容量（15 度倾斜配置） | ||
| 加注时更换滤清器 | |
|
| 加注时不更换滤清器 | |
|
| "添加"和"满"标记之间的容量 | |
|
为了正确保养冷却系统，必须确定冷却系统总容量。 冷却系统的总容量将随安装的设备不同而变化。 冷却系统的总容量可包括以下部件：发动机、膨胀箱、热交换器、散热器、船冷却器和管道。
参考由 Caterpillar或安装设备的原始设备制造商（OEM）提供的规范。 在下列表格中记录冷却系统的总容量。
Show/hide table
| C175-16 加注容量 | |
| 冷却系统 | 容量 |
| 水套水 | |
| 独立回路后冷式 | |
Caterpillar Information System:
C7.1 Marine Engine Water Temperature Regulator - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Conveyor Swing) - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks Event Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Diagnostic Trouble Codes
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks Solenoid Valve - Test - Engine
C175 Tier 4 Final Engines for Off-Highway Trucks Solenoid Valve - Test - Aftertreatment
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Exhaust Has Excessive White Smoke
Fuel Line Serviceability for Certain Tier 4 C175 Engines {1100, 1101, 1252} Fuel Line Serviceability for Certain Tier 4 C175 Engines {1100, 1101, 1252}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Exhaust Temperature Is High
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
Relay Compatibility Issue on Continuous Oil Prelube on 3508 Fire Pump Engines {1319} Relay Compatibility Issue on Continuous Oil Prelube on 3508 Fire Pump Engines {1319}
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Conveyor Lift) - Remove and Install
C175-16 Oil and Gas Generator Set Maintenance Recommendations
C175-16 Oil and Gas Generator Set Marine Classification Society Certification Requirements
C7.1 Marine Engine Rocker Arm and Shaft - Remove
C7.1 Marine Engine Rocker Arm and Shaft - Install
G3512 Generator Set Maintenance Interval Schedule - Standby
G3512 Generator Set Maintenance Interval Schedule - Load Management/Continuous
C7.1 Marine Engine Camshaft - Remove
C7.1 Marine Engine Camshaft - Install
New Engine Software on Certain C4.4 Generator Sets {1901, 1920} New Engine Software on Certain C4.4 Generator Sets {1901, 1920}
G3512 Generator Set Speed Sensor - Clean/Inspect
349F and 352F Excavators Fuses - Replace