1. Home
  2. Caterpillar
  3. Disassembly and Assembly
  4. #i06516729

C11 and C13 Engines for Caterpillar Built Machines Caterpillar


Gear Group (Rear) - Remove and Install

Usage:

D8N 1XJ

Prosedur Pelepasan

Show/hide table
Tabel 1
Alat yang Diperlukan 
Alat  Nomor Suku Cadang  Keterangan Suku Cadang  Jml 
A  1P-0520  Group Penggerak.  1 
B  1P-0510  Group Penggerak  1 

Dimulai dengan:

  1. Lepaskan motor starter elektrik.

  2. Lepaskan flywheel.

  1. Penopang engine.
    Show/hide table
    Ilustrasi 1g06002548

  2. Lepaskan baut (2) dan seal crankshaft belakang (1).
    Show/hide table
    Ilustrasi 2g06002556

  3. Lepaskan baut (4) dan ring. Lepaskan penutup (3) dan seal.
    Show/hide table
    Ilustrasi 3g06002558

  4. Lepaskan roda gigi (7), baut (6), dan roda gigi (5).
    Show/hide table
    Ilustrasi 4g06002564

  5. Lepaskan seal O-ring (8) dari roda gigi (7).
    Show/hide table
    Ilustrasi 5g06172622

  6. Gunakan Peralatan (A) untuk melepaskan bushing (7A) dari rakitan roda gigi (7).
    Show/hide table
    Ilustrasi 6g06172537

  7. Lepaskan baut (9), rakitan adaptor (10), dan seal O-ring.
    Show/hide table
    Ilustrasi 7g06172541

  8. Gunakan Peralatan (B) untuk melepaskan bearing (11) dari rakitan adaptor (10).
    Show/hide table
    Ilustrasi 8g06172549

  9. Lepaskan rakitan roda-gigi (12).
    Show/hide table
    Ilustrasi 9g06172554

  10. Lepaskan penutup (13) dan seal O-ring.
    Show/hide table
    Ilustrasi 10g06172557

  11. Gunakan Peralatan (B) untuk melepaskan bearing (14).

Prosedur Pemasangan

Show/hide table
Tabel 2
Alat yang Diperlukan 
Alat  Nomor Suku Cadang  Keterangan Suku Cadang  Jml 
A  095-0706  Baut  2 
    Show/hide table
    Ilustrasi 11g06172557
    Show/hide table
    Ilustrasi 12g06172580
    Show/hide table
    Ilustrasi 13g06172587

  1. Turunkan temperatur bearing (14). Pastikan untuk mencocokkan Dimensi (B) dan Dimensi (C) saat memasang bearing (14). Dimensi (B) menandakan sudut sambungan pada bearing (14). Dimensi (B) adalah 15° ± 1°. Dimensi (C) menunjukkan jarak dari bearing (14) ke bagian ujung lubang. Dimensi (C) adalah 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
    Show/hide table
    Ilustrasi 14g06172554

  2. Pasang seal O-ring dan penutup (9).
    Show/hide table
    Ilustrasi 15g06172597

  3. Pasang rakitan roda gigi (12) dengan sumbat saluran oli (12A) menghadap keluar.
    Show/hide table
    Ilustrasi 16g06172601
    Show/hide table
    Ilustrasi 17g06172609

  4. Turunkan temperatur bearing (11). Pastikan untuk mencocokkan Dimensi (F) dan Dimensi (G) saat memasang bearing (11) pada rakitan adaptor (10). Dimensi (F) menandakan sudut sambungan pada bearing (11). Dimensi (F) adalah 15° ± 1°. Dimensi (G) menunjukkan jarak dari bearing (11) ke bagian ujung lubang. Dimensi (G) adalah 3.500 ± 0.500 mm (0.1378 ± 0.0197 inch).
    Show/hide table
    Ilustrasi 18g06172537

  5. Pasang seal O-ring, rakitan adaptor (10), dan baut (9).
    Show/hide table
    Ilustrasi 19g06172619

  6. Turunkan temperatur bearing (7A). Pasang bearing (7A) pada rakitan roda gigi (7). Pastikan masing-masing relief (H) berada sekitar 2° dari masing-masing relief pada rakitan roda gigi (7).
    Show/hide table
    Ilustrasi 20g06002564

  7. Pasang seal O-ring (8) pada roda gigi (7).
    Show/hide table
    Ilustrasi 21g06002578

  8. Pasang roda gigi (5) dan baut (6).

    Catatan: Peralatan (A) digunakan untuk menopang roda gigi (7) selama pemasangan penutup dan seal crankshaft belakang.

    Catatan: Lubang baut di roda gigi (7) tidak simetris. Saat memasang Peralatan (C), pastikan lubang baut lainnya di roda gigi (7) telah disejajarkan dengan lubang di crankshaft.

  9. Pasang roda gigi (7) dan Peralatan (C).
    Show/hide table
    Ilustrasi 22g06002581

  10. Pasang penutup (3), seal, baut (4), dan ring.
    Show/hide table
    Ilustrasi 23g06002592

  11. Pasang seal crankshaft belakang (1) dan baut (2).

  12. Lepaskan Alat (C).

Diakhiri dengan:

  1. Pasang flywheel.

  2. Pasang motor starter elektrik.

Caterpillar Information System:

C11 and C13 Petroleum Engines Gear Group (Rear) - Remove and Install
C1.7 and C2.2 Industrial Engine Relay - Test - Start Relay
C12.9 Marine Engines Engine Speed/Timing Sensor - Clean/Inspect
Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556} Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556}
New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555} New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555}
C1.7 and C2.2 Industrial Engine Motorized Valve - Test
Preventing Track Roller & Idler Duo-Cone Seal Packing in Freeze-Thaw Conditions {4159, 4180} Preventing Track Roller & Idler Duo-Cone Seal Packing in Freeze-Thaw Conditions {4159, 4180}
C1.7 and C2.2 Industrial Engines Fuel Filter Base - Secondary Fuel Filter Base
C1.7 and C2.2 Industrial Engine Electrical Power Supply - Test
312F and 313F Excavator Machine System Specifications Liquid Level Sensor (Water Separator)
New Software Is Available for Certain 3516C Petroleum Engines {1901, 1920, 7620} New Software Is Available for Certain 3516C Petroleum Engines {1901, 1920, 7620}
A New Fuel Injector Bypass Group Is Now Used on Certain C175 Commercial Engines {1274, 1702} A New Fuel Injector Bypass Group Is Now Used on Certain C175 Commercial Engines {1274, 1702}
Cat® Command For Hauling E1189
New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059} New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059}
New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137} New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137}
A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258} A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258}
C12.9 Marine Engines Starting Aid (Air Inlet Heater) - Inspect/Clean/Replace
C18 Generator Set Engines Fuel Priming Pump - Remove and Install
C12.9 Marine Engines Sensors and Electrical Components
New Scraper Mounting for Certain Asphalt Compactors {6607} New Scraper Mounting for Certain Asphalt Compactors {6607}
G3516 TA Engine Electronic Control System Operation
G3516 TA Engine Engine Governing
New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920} New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920}
New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900} New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900}
Back to top
Contacts My AVS
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.