Fuel Filter Base - Secondary Fuel Filter Base
Show/hide table
| NOTICE |
|---|
|
Refer to Systems Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system. |
If necessary, install a new fuel filter to canister (5). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Show/hide table
| |
| Illustration 1 | g06005288 |
|
Typical example | |
(1) Tighten the bolts to the following torque. ...
(2) Tighten the bolts to the following torque. ...
(3) Tighten the elbow to the following torque. ...
(4) Tighten the vent screw to the following torque. ...
(6) Tighten the elbow to the following torque. ...
Caterpillar Information System:
C1.7 and C2.2 Industrial Engine Electrical Power Supply - Test
312F and 313F Excavator Machine System Specifications Liquid Level Sensor (Water Separator)
New Software Is Available for Certain 3516C Petroleum Engines {1901, 1920, 7620} New Software Is Available for Certain 3516C Petroleum Engines {1901, 1920, 7620}
A New Fuel Injector Bypass Group Is Now Used on Certain C175 Commercial Engines {1274, 1702} A New Fuel Injector Bypass Group Is Now Used on Certain C175 Commercial Engines {1274, 1702}
A New Cylinder Pack Assembly Is Now Available For Certain 3500 Locomotive Engines {1239} A New Cylinder Pack Assembly Is Now Available For Certain 3500 Locomotive Engines {1239}
Quick Coupler (Dedicated Wedge Lock) Quick Coupler - Lubricate
3516E Generator Set Engines Connecting Rod and Main Bearing Journals
C175-16 Locomotive Engine Fuel Filter Is Restricted
C1.7 and C2.2 Industrial Engine CAN Data Link - Test
3516E Generator Set Engines Inlet Manifold
Groove-less Valve Spring Retainer Installation for Well Stimulation Pumps {5070} Groove-less Valve Spring Retainer Installation for Well Stimulation Pumps {5070}
Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202} Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202}
Preventing Track Roller & Idler Duo-Cone Seal Packing in Freeze-Thaw Conditions {4159, 4180} Preventing Track Roller & Idler Duo-Cone Seal Packing in Freeze-Thaw Conditions {4159, 4180}
C1.7 and C2.2 Industrial Engine Motorized Valve - Test
New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555} New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555}
Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556} Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556}
C12.9 Marine Engines Engine Speed/Timing Sensor - Clean/Inspect
C1.7 and C2.2 Industrial Engine Relay - Test - Start Relay
C11 and C13 Petroleum Engines Gear Group (Rear) - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove and Install
Cat® Command For Hauling E1189
New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059} New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059}
New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137} New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137}
A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258} A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258}