3512, 3508 and 3516 Generator Sets Caterpillar


Maintenance Interval Schedule - Standby

Usage:

3508 ZAB
在进行任何操作或维护步骤之前,确保已阅读并理解所有的安全信息、警告和说明。

经授权的操作员可以进行日常保养工作。 经授权的操作员可以进行每周保养工作。 所有其他保养周期中推荐的保养工作必须由经授权的维修技师或由您的 Cat 代理商执行。

用户对所有保养行为负责,包括以下内容:执行所有调整, 使用正确的润滑剂、油液和滤清器 和 用新部件更换正常磨损和老化的旧部件。

未能遵照正确的保养周期和步骤可能导致产品性能降低和/或部件磨损加速。

在进行每个后续周期的保养之前,必须先进行前一个周期的所有保养。

选择先到的间隔以确定正确的保养周期: 燃油消耗量, 工时 和 日历时间。 在恶劣作业条件下工作的产品可能需要更频密的保养。

所有以下情况会影响换油周期:工作条件, 燃油类型, 机油类型 和 集油槽尺寸。 定期机油取样可以分析旧机油,以便确定换油周期是否适合于您的特定发动机。

请参考本操作和保养手册, "发动机机油和滤清器 - 更换" 以确定适合于您的特定发动机的换油周期。

为了确定大修保养周期,请参考本操作和保养手册, "保养建议 "。

除非另有说明,否则应在下列情况下进行保养和修理:

起动系统无法起动。

发动机停机。

发电机不会引起电击危险。

断开发电机的负载。

需要时即进行的保养

蓄电池的回收
蓄电池 - 更换
蓄电池或蓄电池电缆 - 断开
断路器-复位
燃油系统 - 充油
燃油系统粗滤器/油水分离器 - 放水
发电机 -干燥处理
发电机轴承 - 润滑
发电机组 - 测试
发电机组对中 - 检查
发电机绕组 - 测试
锌棒 - 检查/更换

每周

进气滤清器 - 检查 / 清洁 / 测试
空气起动马达润滑器油位-检查
储气罐水和沉积物-排放
最大起动/停机 - 检查
蓄电池充电器 - 检查
蓄电池电解液液位 - 检查
控制面板 - 检查/测试
冷却液液位 - 检查
电接头-检查
发动机空气滤清器保养指示器 - 检查
发动机空气预滤器 - 检查/清洁
发动机机油油位 - 检查
燃油箱中的水和沉渣 - 排放
发电机 - 检查
发电机轴承温度 - 测试/记录
发电机导线 - 检查
发电机负载 - 检查
水套水加热器 - 检查
功率因数 - 检查
空间加热器 - 测试
备用发电机组保养建议
定子绕组温度 - 测试
电压和频率 - 检查
围绕检查

Every 50 Service Hours

锌棒 - 检查/更换

初次250工作小时

发动机气门间隙-检查
燃油喷油器 - 检查/调整

每 6 个月

冷却剂样品 (一级) – 取样

每年的保养

空气切断阀 - 测试
空气起动马达润滑器油杯-清洗
交流发电机 - 检查
皮带 - 检查/调整/更换
冷却剂样品 (二级) – 取样
冷却系统冷却液补充添加剂(SCA) - 测试/添加
曲轴减振器 - 检查
发动机 - 清洁
发动机空气滤清器滤芯(双滤芯)- 检查/清洁/更换
发动机空气滤清器滤芯(单滤芯) - 检查/清洁/更换
发动机曲轴箱呼吸器 - 清洗
发动机安装支座 - 检查
发动机机油油样 - 采样
发动机机油和滤清器 - 更换
发动机保护装置 - 检查
发动机气门间隙-检查
风扇传动轴承 - 润滑
燃油控制机构 – 检查/润滑
燃油喷油器 - 检查/调整
燃油系统粗滤器(油水分离器)滤芯 - 更换
燃油系统细滤清器 - 更换
发电机轴承 - 检查
发电机组振动 - 测试/记录
发电机绕组绝缘 - 测试
软管和卡箍 - 检查/更换
预润滑泵-检查
散热器 - 清洁
旋转整流器-检查
松动传感器-清洁/检查
起动马达 - 检查
定子引线 - 检查
变阻器 - 检查
水泵 - 检查

每3年

冷却液 (DEAC) - 更换
冷却液延长剂(ELC)- 添加
冷却液温度调节器 - 更换
涡轮增压器 - 检查

每6年

冷却液(ELC)- 更换

试运转

发电机组对中 - 检查

Caterpillar Information System:

Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159} Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159}
3512, 3508 and 3516 Generator Sets Maintenance Interval Schedule - Prime Power
Installation Procedure for the Jacket Water Bypass Tube Bracket on Certain 3512C Engines{1380} Installation Procedure for the Jacket Water Bypass Tube Bracket on Certain 3512C Engines{1380}
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger - Remove and Install
C13 Industrial Engine Intake Manifold Air Pressure Is Low
C175-16 Locomotive Engine Turbocharger Turbine Temperature Is High
2014/11/21 A New Jacket Water Bypass Bracket Is Used on Certain 3512C Engines {1380}
C13 Industrial Engine Fuel Pressure Is Low
2014/10/27 New Guidelines for Valve Cover Base Threaded Insert on C27 and C32 Engines {1107, 1120}
2014/10/27 An Improved Installation Procedure for the Injector Top O-Ring Seal on C27 and C32 Machine Engines {1251, 1254, 1290, 1713}
PM3500 Power Modules Maintenance Interval Schedule - Prime Power
2015/02/27 A New Turbocharger and Turbocharger Housing Are Used for CertainG3516B Engine {1052}
3512E Tier 4 Final Engines for Land Electric Drilling Speed Control - Test
3512E Tier 4 Final Engines for Land Electric Drilling Coolant Level Is Low
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Signal (Analog, Passive) - Test
C280-08 Tier 4 Engine Fuel Priming Pump - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Signal (Analog, Active) - Test
C4.4 Engines General Information
Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153} Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153}
3500 Generator Sets Maintenance Interval Schedule - Standby
2014/11/14 New EMCP 3.2/3.3 Software Is Now Available For Use On Certain Cat® Products {4490, 7620}
793F Off-Highway Truck Fuel Correction Factor - Set
3500 Generator Sets Maintenance Interval Schedule - Prime Power
3500 Generator Sets Maintenance Interval Schedule - High Displacement
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.