Engine Oil Pressure Sensor - Remove and Install - Filtered and Unfiltered
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Isolate the electric power generation set. Refer to Operation and Maintenance Manual, "Generator Isolating for Maintenance" for the correct procedure.
Show/hide table
Illustration 1 g03707418 - Disconnect the harness assembly and remove filtered engine oil pressure sensor (1).
- Remove the O-ring seal from the engine oil pressure sensor.
Show/hide table
Illustration 2 g03707419 - Disconnect the harness assembly and remove unfiltered engine oil pressure sensor (2).
- Remove the O-ring seal from the engine oil pressure sensor.
- Install engine oil pressure sensors (1) and (2) in the reverse order of removal. tighten to a torque of
- Tighten engine oil pressure sensors (1) and (2) to a torque of
10 ± 2 N·m (89 ± 18 lb in) .
- Tighten engine oil pressure sensors (1) and (2) to a torque of
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Level - Check
PM820, PM822, and PM825 Cold Planer Track Drive - Inspect
PM820, PM822, and PM825 Cold Planer Steering Cylinder Ends - Lubricate
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Temperature Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Rotor Service Door Pivot Pins - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Level - Check
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil - Change
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Sample - Obtain
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Level - Check
2014/08/01 A New Alternator and Mounting Hardware Are Used For Certain G3306B Engines {1405}
Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916} Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916}
2014/08/08 New Engine Software Is Used on Certain 3512C Well Fracturing Engines {1901, 1920}
2014/08/15 New Turbocharger Support Bolts Are Used on 3512C HD Drilling Engines {1052, 7553}
2014/08/15 New Oil Cooler and Turbochargers Are Available for Certain 3512C Land Drilling Engines {1052, 1053, 1378}
2014/10/03 New Aftercooler Elbow Mounting Brackets Are Now Used On Certain 3600 and C280 Engines {1063, 1063}
460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
G3516 TA Engine Fuel Pressure Is High
460-9243 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9243 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
G3516 TA Engine Fuel Pressure Is Low
460-9353 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9353 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C3.4B Engines Oil Contains Fuel