Turbocharger Inlet Temperature Sensor - Remove and Install
Note: This procedure applies to both turbocharger inlet temperature sensors.
- Isolate the electric power generation set. Refer to Operation and Maintenance Manual, "Generator Isolating for Maintenance" for the correct procedure.
Show/hide table
Illustration 1 g03707376 - Disconnect harness (1) and remove turbocharger inlet temperature sensor (2).
- Remove the O-ring seal from the turbocharger inlet temperature sensor.
- Install turbocharger inlet temperature sensor (2) in the reverse order of removal.
- Tighten turbocharger inlet temperature sensor (2) to a torque of
20 ± 3 N·m (177 ± 27 lb in) .
- Tighten turbocharger inlet temperature sensor (2) to a torque of
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Rotor Service Door Pivot Pins - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Level - Check
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil - Change
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Sample - Obtain
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Level - Check
XQC1200 and XQC1600 Power Modules Temperature Sensor (Exhaust) - Remove and Install
C8.7 Marine Engine Crankshaft Vibration Damper - Inspect
XQC1200 and XQC1600 Power Modules Inlet Manifold Temperature Sensor - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet Manifold Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Steering Cylinder Ends - Lubricate
PM820, PM822, and PM825 Cold Planer Track Drive - Inspect
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Level - Check
XQC1200 and XQC1600 Power Modules Engine Oil Pressure Sensor - Remove and Install - Filtered and Unfiltered
2014/08/01 A New Alternator and Mounting Hardware Are Used For Certain G3306B Engines {1405}
Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916} Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916}
2014/08/08 New Engine Software Is Used on Certain 3512C Well Fracturing Engines {1901, 1920}
2014/08/15 New Turbocharger Support Bolts Are Used on 3512C HD Drilling Engines {1052, 7553}
2014/08/15 New Oil Cooler and Turbochargers Are Available for Certain 3512C Land Drilling Engines {1052, 1053, 1378}
2014/10/03 New Aftercooler Elbow Mounting Brackets Are Now Used On Certain 3600 and C280 Engines {1063, 1063}
460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
G3516 TA Engine Fuel Pressure Is High