Component Location
Block Diagram for the 3500 Engine
Show/hide table
| |
| Illustration 1 | g03331448 |
Show/hide table
| |
| Illustration 2 | g01189857 |
|
Typical block diagram for the generator control | |
Show/hide table
| |
| Illustration 3 | g01189902 |
|
Typical block diagram for communications | |
Show/hide table
| |
| Illustration 4 | g03331815 |
|
Typical left-hand side view (1) Engine coolant temperature sensor (2) Air inlet manifold temperature sensor (3) Exhaust port temperature sensor (4) Left turbocharger turbine inlet temperature sensor (5) Left air shutoff valve (6) Left turbocharger compressor inlet pressure sensor (7) Electronic Modular Control Panel (EMCP) (8) Magnetic speed sensor (9) Engine speed / timing sensor (10) Power distribution box (11) Jacket water heater (12) Detonation sensor (13) Service tool connector (14) Separate circuit aftercooler water inlet temperature sensor | |
Show/hide table
| |
| Illustration 5 | g03331816 |
|
Typical right-hand side view (15) Right turbocharger compressor inlet pressure sensor (16) Right air shutoff valve (17) Right turbocharger turbine inlet temperature sensor (18) Crankcase pressure sensor - Either cylinder 1 or 5 (19) Prelube pump (20) Gas regulator (21) Fuel heater (22) Gas shutoff valve (GSOV) (23) Fuel control valve (24) ISM connector J1/P1 (25) ISM connector J2/P2 (26) Air start solenoid (27) Oil temperature sensor | |
Show/hide table
| |
| Illustration 6 | g03331812 |
|
Typical front view of right-hand fuel service (28) Unfiltered fuel pressure sensor (29) Filtered fuel pressure sensor (30) Filtered oil pressure sensor (31) Atmospheric pressure sensor (32) ECM connector J2/P2 (33) ECM connector J1/P1 (34) Air inlet manifold pressure sensor (35) Unfiltered oil pressure sensor | |
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Power Sources
C4.4 Engines for Caterpillar Built Machines Electronic Control System
C4.4 Engines for Caterpillar Built Machines Clean Emissions Module - Diesel Oxidation Catalyst (DOC), Diesel Particulate Filter (DPF) and Selective Catalytic Reduction (SCR) System
C4.4 Engines for Caterpillar Built Machines Clean Emissions Module - Diesel Oxidation Catalyst (DOC) and Selective Catalytic Reduction (SCR) System
2014/12/12 New Fuel Injector Rocker Arms Are Used on Certain C13 Commercial Engines {1123}
C4.4 Engines for Caterpillar Built Machines DEF Dosing Control System
Retrofit SCR Aftertreatment Maintenance Interval Schedule
2014/07/03 New Accessory Drives Are Used on Certain 3500 Machine Engines {1207}
797 Off-Highway Truck Hydraulic System Hoist System - Oil Makeup - If Equipped
421-1011 Valve Recession Tool Group used on G3500 C, E, ; H Engines{0374, 0599, 0701, 0703, 1100} 421-1011 Valve Recession Tool Group used on G3500 C, E, & H Engines{0374, 0599, 0701, 0703, 1100}
797 Off-Highway Truck Manual Lowering (Powered Stairway) - Test - If Equipped
2014/06/13 Additional Diesel Particulate Filter (DPF) Ash Service Cleaning Interval Information Is Now Used On Certain Tier 4 Interim and Tier 4 Final C7.1 - C18 Engines {108F}
C9 Generator Set Model View Illustrations
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C7.1 Commercial Marine Engine Welding Precaution
2014/06/20 New Software Is Used on Certain G3516B 1500 RPM Generator Set Engines {1901, 1920}
C7.1 Generator Sets Model View Illustrations
C7.1 Generator Sets Product Description
C7.1 Generator Sets Refill Capacities
C7.1 Generator Sets Voltage Regulators
336F XE Excavator Machine System Specifications Coupler Lines
C3.4B Industrial Engine Safety Messages
C3.4B Industrial Engine Burn Prevention
C3.4B Industrial Engine Fire Prevention and Explosion Prevention