Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8T-0914(1) | Guide Pin | 2 |
B | 1U-9392(1) | Damper Guide Pin | 2 |
(1) | Part of 9U-5105 Engine Tool Group |
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Select the correct Tooling in accordance with the proper application.
- Remove two bolts (1) that hold vibration damper (2). Install Tooling (B) in the adapter.
- Install a suitable lifting device through the center of vibration damper (2). The weight of a narrow vibration damper is approximately
288 kg (639 lb) . The weight of a wide vibration damper is approximately402 kg (886 lb) . - Remove the rest of bolts (1) that hold vibration damper (2) to the adapter. Slide the vibration damper along Tooling (B) and remove vibration damper (2). Remove Tooling (B).
Show/hide table
Illustration 3 g01294011 - Remove the two top bolts that hold adapter (3) and vibration damper (4). Install Tooling (A).
- Remove the rest of the bolts and remove adapter (3).
Show/hide table
Illustration 4 g01294025 - Move vibration damper (4) onto Tooling (A) until a suitable lifting device can be placed through the center of vibration damper (4).
- Install a suitable lifting device through the center of vibration damper (4). The weight of a narrow vibration damper is approximately
288 kg (639 lb) . The weight of a wide vibration damper is approximately402 kg (882 lb) . Remove vibration damper (4).Show/hide tableIllustration 5 g00609918 - Remove spacer (5).
Note: For information on rebuilding vibration dampers, refer to Reuse and Salvage Guidelines, SEBF8152, "Procedures to Rebuild Vibration Dampers for 3600 Family of Engines".
Illustration 1 | g00609902 |
Dual Vibration Dampers |
Illustration 2 | g00609906 |
Note: The later vibration dampers have finned covers. Be careful not to damage the fins.
- Install Tooling (A) in the crankshaft.
- Place spacer (5) in position on Tooling (A). Be sure that the heads of the bolts that hold the adapter assembly together fit into the holes in spacer (5).
Show/hide table
Illustration 7 g01294025 - Install a suitable lifting device through the center of vibration damper (4). The weight of a narrow vibration damper is approximately
288 kg (639 lb) . The weight of a wide vibration damper is approximately402 kg (882 lb) . - Place vibration damper (4) on Tooling (A). Align the Timing Mark for the TC position on vibration damper (4) with the Timing Mark on the crankshaft. Be sure that the bolt holes are aligned. Be sure that the heads of the small bolts at the center of the vibration damper fit into the spacer. Install vibration damper (4).
Show/hide table
Illustration 8 g01294011 - Install adapter (3) on Tooling (A). Be sure that the bolt holes are aligned. Be sure that the heads of the small bolts at the center of vibration damper (4) fit into adapter (3).
- Install the bolts that hold the adapter to the crankshaft. Tighten the bolts in a diagonal pattern to a torque of
1350 ± 150 N·m (1000 ± 110 lb ft) . - Remove Tooling (A) and install Tooling (B) in adapter (3).
Note: Ensure that the outer vibration damper is installed in the correct orientation. The Timing Mark for the TC position should be turned 36 degrees in a clockwise direction from the Timing Mark for the TC position on vibration damper (4). The direction is determined when the dampers are viewed from the front of the engine.
Show/hide tableIllustration 9 g00609906 Show/hide tableIllustration 10 g00609902 Dual Vibration Dampers - Install a suitable lifting device through the center of vibration damper (2). The weight of a narrow vibration damper is approximately
288 kg (639 lb) . The weight of a wide vibration damper is approximately402 kg (886 lb) . - Install vibration damper (2). Be sure that the bolt holes in the vibration damper are aligned with the threaded holes in the adapter. Be sure that the heads of the small bolts at the center of vibration damper (2) fit into the adapter.
- Install bolts (1) that hold vibration damper (2) to the adapter. Remove Tooling (B). Install remaining bolts (1). Tighten the bolts in a diagonal pattern to a torque of
1350 ± 150 N·m (1000 ± 110 lb ft) .
Illustration 6 | g00609918 |