Oil Temperature Regulators - Remove and Install
Show/hide table
Required Tool | |||
Tool | Part Number | Part Description | Qty |
A | 221-8647 | Seal Installer Gp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the engine oil from the oil temperature regulator housing. Refer to Operation and Maintenance Manual, "Engine Oil - Change" for the correct draining procedure.
Show/hide table
Illustration 1 g00554514 Typical Example - Disconnect sending unit (4) from the cover if a sending unit is installed.
- Remove the bolts that hold cover (2) to oil temperature regulator housing (1).
- Remove cover (2) and tube (3).
Show/hide table
Illustration 2 g00554516 Note: It is not necessary to remove oil temperature regulator housing (1) from the engine in order to remove oil temperature regulators (5).
- Remove the gasket and oil temperature regulators (5) from oil temperature regulator housing (1).
- Remove the lip seals from oil temperature regulator housing (1).
- Use Tooling (A) in order to install the lip seals in oil temperature regulator housing (1) with the lip of the seal away from cover (2).
- Install oil temperature regulators (5) in oil temperature regulator housing (1).
- Install new O-ring seals on tube (3). Apply clean engine oil to the O-ring seals.
- Place tube (3), cover (2), and the gasket in position on oil temperature regulator housing (1). Install the bolts that hold tube (3), cover (2), and the gasket in position.
- Connect sending unit (4) to the cover.
- Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil - Change" for the correct filling procedure.
Show/hide table
Illustration 3 | g00554516 |
Show/hide table
Illustration 4 | g00554514 |
Caterpillar Information System:
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Engine Oil Pan - Remove and Install
374F and 390F Excavators Tool Control System One-Way/Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C4.4 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C4.4 Marine Generator Set Coolant Temperature Is High
C4.4 Marine Generator Set Coolant Level Is Low
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install