Engine Oil Pan - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Studs 1/2 - 13 by 5 inch |
4 |
Start By:
- Remove the prelubrication oil pump.
- Install the engine lifting brackets.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove the bolts and clamps that hold the tube assembly to engine oil pan (4).
- Remove bolts (2). Remove spacer (1). Remove the tube assembly from engine oil pan (3) and the engine oil pump.
- Ensure that all connections between the cylinder block and engine oil pan (3) have been removed.
- Attach a suitable lifting device to the engine lifting brackets. The weight of the C280-12 Engine is approximately
26000 kg (57300 lb) . The weight of the C280-16 Engine is approximately30000 kg (66100 lb) . Remove bolts (4) that hold engine oil pan (3) to the cylinder block and the end covers. Remove the engine from the base. - Place the engine on support blocks. The minimum height of the stands should be
671 mm (26.4 inch) for the removal of the engine oil pan.Show/hide tableIllustration 3 g03744427 - Place a pallet jack under each end of engine oil pan (3). The weight of the C280-12 engine oil pan is approximately
628 kg (1385 lb) . The weight of the C280-16 engine oil pan is approximately661 kg (1457 lb) . - Raise the pallet jacks in order to support engine oil pan (3).
Show/hide table
Illustration 4 g03744428 - Remove gasket (5) from engine oil pan (3).
Show/hide table
Illustration 1 | g03744425 |
Typical Example |
Show/hide table
Illustration 2 | g03744426 |
Typical Example |
- Clean the gasket surface of the engine oil pan and the cylinder block. Install a new gasket (5) on engine oil pan (4).
Note: Check the inside of the engine oil pan in order to ensure that all of the Tooling has been removed. Ensure that there is nothing under the suction bell.
- Attach a suitable lifting device to the engine lifting brackets. The weight of the C280-12 Engine is approximately
26000 kg (57300 lb) . The weight of the C280-16 Engine is approximately30000 kg (66100 lb) . Place the engine on support blocks.Show/hide tableIllustration 6 g03744427 - Move engine oil pan (4) into position under the cylinder block. The weight of the C280-12 engine oil pan is approximately
628 kg (1385 lb) . The weight of the C280-16 engine oil pan is approximately661 kg (1457 lb) . - Install Tooling (A) at each corner of engine oil pan (4). Use a pallet jack in order to raise engine oil pan (4) into position.
Show/hide table
Illustration 7 g03744426 Typical Example Show/hide tableIllustration 8 g03744425 Typical Example - Install bolts (3).
- Place the tube assembly and spacer (1) in position. Install bolts (2).
Note: Lubricate the O-ring seals with clean engine oil before installation.
- Install the clamps and bolts that hold the tube assembly to engine oil pan (4).
Show/hide table
Illustration 5 | g03744428 |
End By:
- Remove the engine lifting brackets.
- Install the prelubrication oil pump.
Caterpillar Information System:
374F and 390F Excavators Tool Control System One-Way/Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C4.4 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C4.4 Marine Generator Set Coolant Temperature Is High
C4.4 Marine Generator Set Coolant Level Is Low
C4.4 Marine Generator Set Coolant Contains Oil
C4.4 Marine Generator Set Battery Problem
C4.4 Marine Generator Set Alternator Problem
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install