Relief Valve (Pilot) - Test and Adjust
技术规格
Show/hide table
"安全阀(先导)- 测试和调整"     | |||
---|---|---|---|
项目     | 机器设定     | 技术规格     | 实际值     |
先导安全阀     | 转速刻度盘 "1" AEC 开关 OFF     |
3950 ± 200 kPa (573 ± 29 psi)     |
    |
转速刻度盘 "10" AEC 开关 OFF |
4200 ± 200 kPa (609 ± 29 psi)     |
    |
简介
先导安全阀位于先导歧管上。 先导歧管位于主控制阀下面。 先导安全阀限制先导系统中的压力。 先导安全阀的设定可以调节。
所需工具
Show/hide table
图 1 | g02726620 |
Show/hide table
工具     | 项目     | 数量     | 零件号     | 说明     |
---|---|---|---|---|
B     | B1     | 1     | 8T-0856     | 压力表 6000 kPa (870 psi)     |
B2 | 1     | 6V-3989     | 接头     | |
B3 | 2     | 6V-4143     | 快速连接连接器     | |
B4 | 1     | 177-7862     | 软管组件 5.5 m (18 ft)     |
测试准备
- 将机器停放在平地上。
- 停止发动机。
- 释放液压系统压力。 请参阅测试和调整, "系统压力 - 释放".
- 将一块 6000 kPa (870 psi) 压力表连接至测压口 (1) 。
Show/hide table
图 2 | g03385093 |
先导滤清器 (1) 测压口 (2) 先导滤清器 |
测试步骤
- 起动发动机。
- 将液压油温度提高至 55°± 5°C (131°± 9°F)。
- 将机器控制装置设为以下设置:发动机转速旋钮 "1" 和 AEC 开关 OFF。
- 检查测压口 (1) 处的先导卸压阀设定。
- 先导安全阀设置应为 3950 ± 200 kPa (573 ± 29 psi)。
- 将机器控制装置设为以下设置:发动机转速旋钮 "10" 和 AEC 开关 OFF。
- 检查测压口 (1) 处的先导卸压阀设定。
- 先导安全阀设置应为 4200 ± 200 kPa (609 ± 29 psi)。 如果先导安全阀设定不在技术规格范围内,请调整先导安全阀。
调整步骤
Show/hide table
图 3 | g03385116 |
先导歧管(位于主控制阀下面) (3) 调整螺钉 (4) 锁紧螺母 (5) 先导安全阀 (6) 先导歧管 |
- 如需调整先导卸压阀,请松开锁紧螺母 (4) 。
- 旋转调整螺钉 (3) ,直到测压口 (1) 的压力表读数处在技术规格范围内。
注: 把调整螺钉 (3) 顺时针方向转动,以提高压力。 把调整螺钉 (3) 逆时针方向转动,以降低压力。
注: 压力升高时,务必进行最终压力调整。
- 拧紧锁紧螺母 (4) ,扭矩为 49 ± 5 N·m (36 ± 4 lb ft)。
- 再次测试压力设定。 请参阅"测试步骤"。
注: 进行压力调整需要发动机和泵正常工作。 如果压力调整的结果不正确,则检查发动机和泵的特性曲线。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Install - Wall Flow Diesel Particulate Filter
C32 Generator Set Reference Material
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Install - Through Flow Diesel Particulate Filter
Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101} Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101}
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Wall Flow Diesel Particulate Filter
2013/06/13 Improved 3412 Marine Bundled Repair Solution Foundational Kits Are Available {1000}
C32 Generator Set Sound Information
Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D} Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D}
C32 Generator Set Plate Locations and Film Locations
C13 Engine for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
326F and 330F Excavator Machine Systems Boom Drift Reduction Valve
CG137-08 and CG137-12 Industrial Engines General Information
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Performance - Test
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Substrate - Inspect
C175-16 Locomotive Engine Exhaust Manifold
C175-16 Locomotive Engine Engine Oil Pan
C175-16 Locomotive Engine Crankshaft
C175-16 Locomotive Engine Crankshaft Wear Sleeves and Seals
C7.1 Industrial Engine Nitrogen Oxide Sensor - Remove and Install - Original Equipment Manufacturer (OEM) Exhaust Pipe
CX31 On-Highway Transmission Output Transfer Yoke
C175-16 Locomotive Engine Gear Group (Front)