Inlet and Exhaust Valve Guides - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 444-0978     | 气门导管冲头     | 1     |
开始:
- 拆下进气门和排气门。 请参阅拆解和组装, "进气门和排气门 - 拆卸和安装"。
Show/hide table
注意 |
---|
必须由经过正规培训的专业人员拆卸气门导管和气门座。 还需要使用专用机械设备。 有关更多信息,请咨询授权 Caterpillar 代理商。 |
- 使用工具 (A) 将气门导管 (2) 从缸盖 (1) 上拆下。
Show/hide table
图 1 | g03003636 |
- 有关其余的气门导管,请重复步骤 1。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 444-0978     | 气门导管冲头     | 1     |
435-3148 | 限动环     | 1     | |
B     | 442-7298     | 气门导管铰刀     | 1     |
Show/hide table
注意 |
---|
必须由经过正规培训的专业人员拆卸气门导管和气门座。 还需要使用专用机械设备。 有关更多信息,请咨询授权 Caterpillar 代理商。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁缸盖中用于气门导管的母孔。
- 润滑新的气门导管 (2) 并将气门导管放置到位。 小心轻敲气门导管以开始安装。 使用工具 (A) 将气门导管安装到缸盖中。
Show/hide table
图 2 | g03003639 |
- 对其余的气门导管重复步骤 2。
- 检查气门导管 (2) 的凸出 (X) 。 气门导管应突出气门弹簧凹槽上方 8.5 ± 0.15 mm (0.33465 ± 0.00591 in)。 有关更多资料,请参阅技术规格, "缸盖气门"。
Show/hide table
图 3 | g03005596 |
- 安装气门导管 (2) 后,必须将气门导管铰孔至精加工直径。 遵循步骤 5.a 至 5.c 以便铰孔气门导管。
- 使用清洁的发动机机油润滑气门导管 (2) 的孔。
- 使用工具 (B) 铰大气门导管。 确保作用在工具 (B) 上的压力均匀。
- 确保缸盖清洁且无机加工碎屑。
- 检查气门导管 (2) 的精加工直径。 有关更多资料,请参阅技术规格, "缸盖 - 气门"。
- 检查气门低于缸盖表面的深度。 有关更多资料,请参阅系统操作、测试和调整, "气门深度 - 检查"。
End By: 安装进气阀和排气阀。 请参阅 拆解和组装, "进气门与排气门 - 拆卸和安装"。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Install - Wall Flow Diesel Particulate Filter
C32 Generator Set Reference Material
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Install - Through Flow Diesel Particulate Filter
Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101} Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101}
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Wall Flow Diesel Particulate Filter
2013/06/13 Improved 3412 Marine Bundled Repair Solution Foundational Kits Are Available {1000}
C32 Generator Set Sound Information
Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D} Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D}
C32 Generator Set Plate Locations and Film Locations
Water Delivery System and 777F WTR, 777G WTR and 785D WTR OEM Off-Highway Trucks Service Tools
374F Excavator Machine Systems Relief Valve (Pilot) - Test and Adjust
C13 Engine for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
326F and 330F Excavator Machine Systems Boom Drift Reduction Valve
CG137-08 and CG137-12 Industrial Engines General Information
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Performance - Test
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Substrate - Inspect
C175-16 Locomotive Engine Exhaust Manifold
C175-16 Locomotive Engine Engine Oil Pan
C175-16 Locomotive Engine Crankshaft
C175-16 Locomotive Engine Crankshaft Wear Sleeves and Seals
C7.1 Industrial Engine Nitrogen Oxide Sensor - Remove and Install - Original Equipment Manufacturer (OEM) Exhaust Pipe
CX31 On-Highway Transmission Output Transfer Yoke