Vibration Damper and Pulley - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 M14 x 1.5 x 100 mm     |
1     |
B     | 227-4393     | E18 Torx 套筒     | 1     |
C     | 8T-3052     | 度数轮     | 1     |
D     | -     | 导向螺柱 M12 x1.75 × 50 mm     |
2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保曲轴适配器和曲轴前部清洁且无损坏。
Show/hide table
图 1 | g02368018 |
- 检查减振器 (6) 有无损坏。 如有必要,更换减振器。
- 如有必要,按照步骤 3.a 至 3.e 将减振器、曲轴皮带轮安装到曲轴适配器上。
- 将曲轴适配器 (4) 放到适当的支承上。
- 将工具 (D) 安装到曲轴适配器 (4) 上。
- 将曲轴皮带轮 (5) 和减振器 (6) 安装到工具 (D) 上方。
- 将螺栓 (7) 安装到曲轴皮带轮组件上。
注: 在曲轴皮带轮组件周围等距离布置螺栓 (7) 。
- 拧紧螺栓 (7) 至扭矩为115 N·m (85 lb ft)。
- 如有必要,安装摩擦片 (3) 。 按照步骤 4.a 至步骤 4.b 安装摩擦片 (3) 。
- 安装摩擦片 (3) 。
- 将新前油封安装到前盖上。 有关正确的步骤,请参阅拆解和组装, "曲轴前油封 - 拆卸和安装"。
- 将工具 (A) 安装在曲轴上。
- 将曲轴皮带轮组件 (2) 安装到曲轴上。
Show/hide table
图 2 | g02368017 |
- 将一颗 Torx 螺钉 (1) 安装到曲轴皮带轮组件 (2) 上,用手拧紧。
- 拆下工具 (A) 。
- 将其余 Torx 螺钉 (1) 安装到曲轴皮带轮组件 (2) 上。
- 使用适当的工具,使曲轴固定不动。 拧紧 Torx 螺钉 (1) 至扭矩为 40 N·m (29 lb ft)。
- 使用工具 (B) 和 (C) 将 Torx 螺钉 (1) 再转动 120 度。
End By: 安装交流发电机皮带。 有关正确的步骤,请参阅 拆解和装配, "交流发电机皮带 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Engines Valve Mechanism Cover Base - Remove and Install
C7.1 Engines Valve Mechanism Cover - Remove and Install
C7.1 Engines Turbocharger - Remove - Turbocharger for Top Mounted Engines
C7.1 Engines Turbocharger - Install - Turbocharger for Top Mounted Engines
C7.1 Engines Turbocharger - Remove - Turbocharger for Side Mounted Engines
C7.1 Engines Turbocharger - Install - Turbocharger for Side Mounted Engines
C7.1 Engines Rocker Shaft and Pushrod - Remove
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies AC Interface PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Power Distribution PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Parallel Cabinet Interface PWA
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Parallel Cabinet Controller PWA
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Fan Monitor PWA (MMS System Cabinet)
C7.1 Engines Vibration Damper and Pulley - Remove
C7.1 Engines Wastegate Solenoid - Remove and Install
C7.1 Engines Water Pump - Install
C7.1 Engines Water Pump - Remove
C7.1 Engines Water Separator and Fuel Filter (Primary) - Remove and Install
C7.1 Engines Water Temperature Regulator - Remove and Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System I/O PWA (MMS System Cabinet)
C9 Engine Coolant (DEAC) - Change
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System I/O Daughter PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Transformer (T1 to T3)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies 24V Power Supply (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Current Transformers (Primary, Secondary)