Cylinder Head - Remove and Install
开始:
- 拆下排气歧管。
- 拆下进气歧管。
- 拆下摇臂轴和推杆。
- 拆下电子喷油器。
注: 请参阅技术规格 UENR3421 "发动机设计",了解非指定的发动机扭矩值。
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
Show/hide table
图 1 g03339552 Show/hide table图 2 g03339573 - 按照从 (10) 到 (1) 的相反数字顺序从缸盖 (11) 上逐步拧松缸盖螺栓 (12)。 将缸盖螺栓 (12) 从缸盖 (11) 上拆下。
- 将合适的起吊设备连接到缸盖 (11)。 缸盖 (11) 的重量约为
46 kg (100 lb) 。 - 使用合适的起吊设备将缸盖 (11) 吊离缸体。
Show/hide table
注意 将缸盖放在不会使缸盖表面产生擦伤的表面上。
Show/hide table图 3 g03339590 - 将缸盖密封垫 (13) 从缸体上拆下。
- 记录区域 (A) 中缸盖密封垫槽口的位置。 请参阅图 3 和图 4。
- 记录定位销在缸体中的位置。
Show/hide table
图 4 g02796320 - 记录区域 (A) 中的槽口数量。
Show/hide table
表 1 缸盖密封垫槽口 缸盖密封垫厚度 活塞头突出或凹入曲轴箱气缸表面 拧紧前 拧紧后 (a)-两个槽口 0.900 mm(0.0354 in) 0.800 mm(0.0315 in) 0.0775 至 0.150 mm(0.00306 至 0.00590 in.) (b)-一个槽口 1.00 mm (0.039 in) 0.900 mm(0.0354 in) 0.150 至 0.250 mm(0.0059 至 0.0098 in.) (c)-没有槽口 1.10 mm (0.043 in) 1.00 mm (0.039 in) 0.250 至 0.343 mm(0.0098 至 0.0135 in.)
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-5592 | 螺纹润滑剂 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 记录区域 (A) 中的槽口数量。 请参阅图 5 和图 6。
- 彻底清洁缸盖与缸体的密封垫表面。 不要损坏缸体缸盖的密封垫表面。 确保没有碎屑进入缸孔、冷却液油道或润滑油油道中。
- 检查定位销是否损坏。 如有必要,更换缸体中的定位销。
Show/hide table
图 6 g03339590 - 检查缸盖的密封垫表面有无变形。 有关更多资料,请参阅技术参数, "缸盖"。 如果缸盖密封垫表面变形超过最大允许限制,应更换缸盖。
- 记录区域 (A) 中缸盖密封垫槽口的位置并参阅表 2。 对准新的缸盖密封垫 (13) 与定位销。
Show/hide table
图 7 g03339552 Show/hide table图 8 g03339573 - 使用适当的起吊设备起吊缸盖 (11)。 缸盖 (11) 的重量约为
46 kg (100 lb) 。 - 对准缸盖 (11) 与缸体。 将缸盖 (11) 安装到缸体上。
注: 确保缸盖正确定位在定位销上。
- 清洁并检查缸盖螺栓 (12)。
- 使用发动机机油润滑缸盖螺栓 (12) 的螺纹和螺栓肩。
- 按照从 (1) 到 (10) 的数字顺序将缸盖螺栓 (12) 安装到缸盖 (11) 上。
- 按照下列步骤拧紧缸盖螺栓:
- 拧紧螺栓 (1) 至 (10) 至扭矩为
35 N·m (26 lb ft) - 拧紧螺栓 (1) 至 (10) 至扭矩为
108 N·m (80 lb ft) - 拧紧螺栓 (1) 至 (10) 至扭矩为
187 to 196 N·m (138 to 144 lb ft)
- 拧紧螺栓 (1) 至 (10) 至扭矩为
- 向冷却系统加注冷却液。 有关正确的加注步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 5 | g02796320 |
结束:
- 安装电子喷油器。
- 安装摇臂轴和推杆。
- 安装进气歧管。
- 安装排气歧管。
Caterpillar Information System:
C175-16 Marine Propulsion Engines Engine Shutdown Occurrence
398-9680 Calibration Test Group{0599, 0706, 1250, 1251, 1252, 1280} 398-9680 Calibration Test Group{0599, 0706, 1250, 1251, 1252, 1280}
2013/01/21 Software Update For Proper Air Fuel Ratio Controller Operation Of Certain G3408 and G3412 Engines {1901, 1920}
2013/01/21 New Fuel Pressure Regulator and Set Screw Are Used for 3600 and C280 Engines {1252, 1254}
C9.3 Industrial Engine Fumes Disposal Filter Element - Replace - Emission Related Component
C3.3B Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install
C32 Marine Generator Set Control Panel - Marine Generator Set Engine Control Panel 3 (MGECP 3)
Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078} Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078}
2013/03/29 New Engine Oil Hoses Are Used on Certain Excavators Equipped with C13 Engines {1308}
2013/02/06 Different Water Temperature Regulators (Thermostats) are Available for G3600 Engines {1355}
C3.3B Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
C3.3B Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C32 Marine Generator Set Safety Messages
C32 Marine Generator Set Model View Illustrations
3516C Locomotive Engine and Generator Set Maintenance Interval Schedule
2013/01/29 Improved Software is Now Used for Petroleum Fracturing Transmissions {7620}
2013/03/01 New Suction Screen and Handle Are Used in 3500 Locomotive Engines {1302, 1302}
Work Area Vision System Maintenance Interval Schedule
C1.5 and C2.2 Industrial Engines ECM Auxiliary Output - Test
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Electronic Control System Operation