Driven Equipment - Check
Perform this Maintenance Procedure Daily
Alignment of the Engine Crankshaft
The alignment between the engine and the driven equipment must be maintained properly in order to minimize the following problems:
- Bearing problems
- Vibration of the engine crankshaft and the driven equipment
Check the alignment according to instructions that are provided by the following manufacturers: Caterpillar, OEM of the coupling and OEM of the driven equipment.
Perform this Maintenance Procedure Every 250 Service Hours
Inspection of the Driven Equipment
Observe the driven equipment during operation. Look for the following items:
- Unusual noise and vibration
- Loose connections
- Damaged parts
Perform any maintenance that is recommended by the OEM of the driven equipment. Refer to the literature of the OEM of the driven equipment for the following service instructions.
- Inspection
- Lubricating grease and lubricating oil requirements
- Specifications for adjustment
- Replacement of components
- Requirements for ventilation
Caterpillar Information System:
Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901} Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901}
336E Excavator Machine System Specifications Final Drive and Motor Fastener (Mounting)
3512C and 3516C Marine Engines Piston and Rings
3512C and 3516C Marine Engines Piston and Rings
Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267} Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267}
Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157} Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157}
Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284} Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284}
Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281} Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281}
Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201} Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201}
3516C Generator Set Engines Temperature Sensor (DEF)
3512C and 3516C Marine Auxiliary Engines Data Link - Test
2012/03/26 New Software Is Used on Certain C18 Industrial Engines {1901, 1920}
2012/09/26 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1059, 1067}
CX48-P2300 Petroleum Transmission Transmission Planetary - Assemble
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Control Panels for the Pumper
Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562} Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562}
2012/03/21 Set the Overspeed Shutdown for C175-16 Petroleum Engines to 115 Percent of Rated Speed {1900, 1907, 1912, 7427}
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Inspect/Test - Gauges and Indicators for the Engine
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Disassemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Assemble
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Assemble
C175-16 Marine Engines Air Inlet and Exhaust System Operation
C175-16 Marine Engines Aftercooler
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Disassemble