Final Drive and Motor Fastener (Mounting)
Show/hide table
Illustration 1 | g03820381 |
Typical example |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | - | - | Before assembly, the surfaces must be clean and free of protective coating. |
2 | 40 | 461-3883 Bolt | Before assembly, remove Anti-Seize compound, oil and dust from bolt, washer and female threads, then apply Loctite C5A Copper Anti-Seize compound to the threads of bolt.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 45 ± 5 degrees. |
Caterpillar Information System:
3512C and 3516C Marine Engines Piston and Rings
3512C and 3516C Marine Engines Piston and Rings
Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267} Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267}
Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157} Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157}
Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284} Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284}
Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281} Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281}
Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201} Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201}
3516C Generator Set Engines Temperature Sensor (DEF)
3512C and 3516C Marine Auxiliary Engines Data Link - Test
2012/03/26 New Software Is Used on Certain C18 Industrial Engines {1901, 1920}
Thermal Spray Procedures for OHT Front Spindles {0679, 4006, 4205} Thermal Spray Procedures for OHT Front Spindles {0679, 4006, 4205}
Thermal Spray Procedures for OHT and WTS Rear Wheel - Bearing Bores {0679, 4201} Thermal Spray Procedures for OHT and WTS Rear Wheel - Bearing Bores {0679, 4201}
Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901} Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901}
SPF343 and SPF343C Trailer Mounted Pumpers Driven Equipment - Check
2012/09/26 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1059, 1067}
CX48-P2300 Petroleum Transmission Transmission Planetary - Assemble
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Control Panels for the Pumper
Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562} Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562}
2012/03/21 Set the Overspeed Shutdown for C175-16 Petroleum Engines to 115 Percent of Rated Speed {1900, 1907, 1912, 7427}
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Inspect/Test - Gauges and Indicators for the Engine
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Disassemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Assemble
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Assemble
C175-16 Marine Engines Air Inlet and Exhaust System Operation