Piston and Rings
Show/hide table
Illustration 1 | g02654636 |
Show/hide table
Specification for 362-9445 Piston and Rod Gp | |||
Item | Qty | Part | Specification Description |
Before assembly of the piston rings, lubricate the ring grooves with clean engine oil. | |||
1 | 1 | 229-1632 Piston Ring | Install with side marked “UP-1” toward top of the piston. |
Thickness of the new ring is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
Increase in clearance for each |
|||
2 | 1 | 144-5695 Piston Ring | Install with side marked “UP-2” toward top of the piston. |
Thickness of the new ring is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
Increase in clearance for each |
|||
3 | 1 | 165-6668 Piston Ring | The ends of the spring coil should be placed 180 degrees from the end gap of the oil control piston rings. |
Thickness of the new ring is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
Increase in clearance for each |
|||
Width of the groove (A) in the piston is |
|||
4 | 1 | 302-3451 Piston Pin | Thoroughly lubricate the piston pin with clean engine oil prior to assembly. |
Diameter is |
|||
Bore of the bushing (C) for piston pin is |
|||
Bore for bushing in the piston is |
|||
5 | 2 | 253-1238 Pin Retainer | Install the pin retainer with the opening towards top of the piston as shown in Illustration 1. |
B | - | - | Lubricate the entire piston to 360 degrees prior to assembly into the cylinder block. Use clean engine oil. |
- | - | - | After installing the piston rings, rotate the piston rings so that the end gaps are placed at 120 degrees distance from each other. |
Caterpillar Information System:
Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267} Thermal Spray Procedures for 772 - 797F OHT Brake Anchor {0374, 0599, 0679, 4251, 4267}
Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157} Thermal Spray Procedures for 3500 Engine - Flywheel Housing {0679, 1157}
Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284} Thermal Spray Procedures for OHT Differential Carrier Assembly {0374, 0599, 0679, 3258, 3281, 3284}
Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281} Thermal Spray Procedures for OHT Differential Housing - Housing and Side Thrust {0374, 0599, 0679, 3258, 3281}
Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201} Thermal Spray Procedures for OHT and WTS Front Wheel - Bearing Bores {0679, 4006, 4201}
3516C Generator Set Engines Temperature Sensor (DEF)
3512C and 3516C Marine Auxiliary Engines Data Link - Test
2012/03/26 New Software Is Used on Certain C18 Industrial Engines {1901, 1920}
Thermal Spray Procedures for OHT Front Spindles {0679, 4006, 4205} Thermal Spray Procedures for OHT Front Spindles {0679, 4006, 4205}
Thermal Spray Procedures for OHT and WTS Rear Wheel - Bearing Bores {0679, 4201} Thermal Spray Procedures for OHT and WTS Rear Wheel - Bearing Bores {0679, 4201}
Thermal Spray Procedures for OHT Rear Spindles {0599, 0679, 4006, 4205} Thermal Spray Procedures for OHT Rear Spindles {0599, 0679, 4006, 4205}
Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162} Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162}
3512C and 3516C Marine Engines Piston and Rings
336E Excavator Machine System Specifications Final Drive and Motor Fastener (Mounting)
Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901} Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901}
SPF343 and SPF343C Trailer Mounted Pumpers Driven Equipment - Check
2012/09/26 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1059, 1067}
CX48-P2300 Petroleum Transmission Transmission Planetary - Assemble
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Control Panels for the Pumper
Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562} Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562}
2012/03/21 Set the Overspeed Shutdown for C175-16 Petroleum Engines to 115 Percent of Rated Speed {1900, 1907, 1912, 7427}
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Inspect/Test - Gauges and Indicators for the Engine
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Disassemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Assemble