There may be several specific safety messages on your generator set. The exact location and a description of the safety messages are reviewed in this section. Please become familiar with all safety messages.
Ensure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if the words cannot be read or if the illustrations are not visible. Use a cloth, water, and soap to clean the safety messages. Do not use solvents, gasoline, or other harsh chemicals. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety messages. The safety messages that are loosened could drop off the engine.
Replace any safety message that is damaged or missing. If a safety message is attached to a part of the engine that is replaced, install a new safety message on the replacement part. Your Caterpillar dealer can provide new safety messages.
Show/hide table
|
|
|
Illustration 1 | g02719682 |
View of the control panel
|
Show/hide table
|
|
|
Illustration 2 | g02721534 |
Side view of the generator set inside the enclosure
|
Show/hide table
|
|
|
Illustration 3 | g02719780 |
Top view of the enclosure
|
Show/hide table
|
|
|
Illustration 4 | g02721430 |
Right side view of the enclosure
|
Show/hide table
|
|
|
Illustration 5 | g02721407 |
Right side view of the open generator set
|
Show/hide table
|
|
|
Illustration 6 | g02721405 |
Left side view of the open generator set
|
Universal Warning (1)
This safety message is located on the enclosure for the control panel.
Show/hide table
|
|
|
Illustration 7 | g01370904 |
Show/hide table
|
Do not operate or work on this equipment unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in serious injury or death. |
|
Automatic Starting (2)
This safety message is located on the sides of the enclosure and on the enclosure for the control panel.
Show/hide table
|
|
|
Illustration 8 | g01392484 |
Show/hide table
|
When the engine is in the AUTOMATIC mode, the engine can start at any moment. To avoid personal injury, always remain clear of the the engine when the engine is in the AUTOMATIC mode. |
|
Electrocution (3)
This safety message is located on the enclosure for the circuit breaker and also on both sides of the enclosure.
Show/hide table
|
|
|
Illustration 9 | g01392482 |
Show/hide table
|
DANGER: Shock/Electrocution Hazard-Do not operate this equipment or work on this equipment unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings will result in serious injury or death. |
|
Show/hide table
|
Do not connect generator to a utility electrical distribution system unless it is isolated from the system. Electrical feedback into the distribution system can occur and could cause personal injury or death.
Open and secure main distribution system switch, or if the connection is permanent, install a double throw transfer switch to prevent electrical feedback. Some generators are specifically approved by a utility to run in parallel with the distribution system and isolation may not be required. Always check with your utility as to the applicable circumstances. |
|
Hot Surface (4)
This safety message is located on the top and sides of the enclosure, as well as near the exhaust, and on the aftercooler.
Show/hide table
|
|
|
Illustration 10 | g01384734 |
Show/hide table
|
Hot parts or hot components can cause burns or personal injury. Do not allow hot parts or components to contact your skin. Use protective clothing or protective equipment to protect your skin. |
|
Crush (5)
This safety message is located on the sides of enclosed generator sets. This safety message is also located on the base for open generator sets.
Show/hide table
|
|
|
Illustration 11 | g01433231 |
Show/hide table
|
Crushing hazard! Read and understand the instructions and warnings in the Operation and Maintenance manual. Failure to follow the instructions or heed the warnings could cause serious injury or death. |
|
Electrical Shock (6)
The safety message for electrical shock is located on the enclosure for the control panel.
Show/hide table
|
|
|
Illustration 12 | g01372247 |
Show/hide table
|
WARNING! Shock/Electrocution Hazard! Read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could cause serious injury or death. |
|
No Step (7)
The safety message for do not step is located on top of the enclosure near both sides.
Show/hide table
|
|
|
Illustration 13 | g00989364 |
Show/hide table
|
Do not use this surface as a step or platform. This surface may not support additional weight or may be slippery. Serious injury or death could occur from a fall. |
|
Hot Fluid Under Pressure (8)
This safety message is located by the cooling system filler cap.
Show/hide table
|
|
|
Illustration 14 | g01371640 |
Show/hide table
|
Pressurized system! Hot coolant can cause serious burns, injury or death. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure. Read and understand the Operation and Maintenance Manual before performing any cooling system maintenance. |
|