Air Inlet and Exhaust Lines
Show/hide table
图 1 | g02553357 |
右视图 |
Show/hide table
图 2 | g02553358 |
螺栓拧紧顺序 |
Show/hide table
技术规格 - 271-0559 空气管路总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 16 | 216-2211 卡箍 | 按照以下步骤拧紧卡箍:
1. 在软管的标记内居中放置卡箍。 2. 调整卡箍的方位,使 T 形螺栓呈 90 度分离。 3. 拧紧至扭矩为 |
2 | 8 | 6V-3917 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
3 | 10 | 8J-5985 螺栓 | 采用以下步骤组装后冷器组件并拧紧螺栓:
1. 将密封组装到后冷器芯上。 2. 临时用胶带将底部密封固定在后冷器上。 不要使用粘接剂、硅润滑剂或任何其它润滑剂来固定密封。 3. 将装了密封的后冷器组装到进气歧管上。 4. 检查底部密封,以确保密封正确座入凹槽内。 5. 安装后冷器盖。 6. 检查顶部密封,以确保密封正确座入凹槽内。 7. 安装盖螺栓。 用手拧紧盖螺栓。 8. 按照图 2 中所示的数字顺序拧紧螺栓至扭矩 9. 按照图 2 中所示的数字顺序将螺栓再次拧紧至 10. 拆下胶带。 |
4 | 12 | 6V-5101 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
Caterpillar Information System:
3500 Engines Air Inlet and Exhaust Lines
C15 Petroleum Engines Configuration Parameters
Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383} Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383}
CG137-08 and CG137-12 Engines Configuration Parameters
C175-16 Petroleum Generator Set Engines Air Prelube Pump Lubricator Bowl - Clean
XQ400 Power Module Control Panel
C15 Petroleum Engines Fan Drive
797F and 797F XQ Off-Highway Truck Hydraulic Fan System System Pressure - Release
C175-16 and C175-20 Generator Set Engines Fuel Injector
3500 Engines Air Inlet and Exhaust Lines
3500 Engines Air Inlet and Exhaust Lines
3500B Engines for Caterpillar Built Power Modules Air Lines
3500 Engines Air Inlet and Exhaust Lines
CG137-08 and CG137-12 Engines Safety Messages
C15 Petroleum Engine Electronic Control System Components
2011/05/11 Drain the Rubber Boot for the Hydraulic Actuators on G3500 and G3600 Engines {1057, 1265}
3500B and 3500C Marine Engines Air Shutoff
3500 Engines Air Shutoff
C15 and C18 Industrial Engines Flywheel
3500 Engines Air Shutoff
C13, C15, and C18 Tier 4 Final Engines Flywheel
C9.3 Tier 4 Final Engines Exhaust Diffuser Adapter
3500 Engines Air Shutoff
C13, C15, and C18 Tier 4 Final Engines Flywheel