Check Valve - Auxiliary Circuit
Show/hide table
| 图 1 | g01526788 |
(1) 123-2537 弹簧
- 在试验力下的长度 ... 33 mm (1.3 in)
- 试验力 ... 9.80 ± 0.49 N (2.2 ± 0.1 lb)
- 试验后的自由长度 ... 53 mm (2.1 in)
- 外径 ... 26.5 mm (1.04 in)
- 试验力 ... 9.80 ± 0.49 N (2.2 ± 0.1 lb)
(2) 在密封的地方，用润滑剂将 O 形密封圈孔稍加润滑。
(3) 在要密封的 2 个支撑环孔上稍涂润滑剂。
注: 拧紧前，将 2P-9063 液压油 涂敷在接头 (4) 的螺纹上。
(4) 接头的扭矩 ... 400 ± 30 N·m (300 ± 22 lb ft)
(5) 239-9040 弹簧
- 在试验力下的长度 ... 30.100 mm (1.1850
in)
- 试验力 ... 11.423 ± 0.571 N (2.6 ± 0.1 lb)
- 试验后的自由长度 ... 39.000 mm (1.5354 in)
- 外径 ... 22.800 mm (0.8976 in)
- 试验力 ... 11.423 ± 0.571 N (2.6 ± 0.1 lb)
Caterpillar Information System:
C6.6 Marine Generator Set Control Panel
C13T-TH35 and C15T-TH35 Petroleum Packages Monitoring System - Dash Lamps and Controls for the Aftertreatment Regeneration Device (ARD)
349F and 352F Excavators Machine System Specifications Relief Valve (Line)
C6.6 Marine Generator Set Indicator Lamps
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Front Lines
C6.6 Marine Generator Set Glossary
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Pilot Lines
C6.6 Marine Generator Set System Overview
319D Excavator Machine System Specifications Pilot Lines - Pump Control and Shuttle Valve
C13, C15, and C18 Generator Set Engines Belt Tightener
C15 Petroleum Generator Set Engines Turbocharger
C9 On-highway Engine Water Lines
C6.6 Marine Generator Set Fuel Injection Lines - Install - Standard Fuel Injection Liners
C6.6 Marine Generator Set Fuel Injection Lines - Remove - Standard Fuel Injection Liners
C11 and C13 Engines Engine Oil Pan
C11 and C13 Engines Engine Oil Pan
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Orifice Tube Assembly - Remove and Install
C175-16 and C175-20 Generator Set Engines Aftercooler Coolant Temperature Is High
Upgrade G3516 and G3512 1400 RPM Gas Compression Engines to ADEM 3 and Air/Fuel Ratio Control with a Nitrogen Oxide Sensor {1000, 1408, 1901, 191N} Upgrade G3516 and G3512 1400 RPM Gas Compression Engines to ADEM 3 and Air/Fuel Ratio Control with a Nitrogen Oxide Sensor {1000, 1408, 1901, 191N}
345D, 349D and 349D2 Excavator Machine System Specifications Pump Lines (Main)
C7 Engines for Caterpillar Built Machines Flywheel Housing
345D, 349D and 349D2 Excavator Machine System Specifications Front Lines
C6.6 Marine Generator Set Control Panel
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Cooling Lines - Hydraulic Oil