Relief Valve (Main) - Assemble
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install O-ring seal (22). Install plug (21). Tighten plug (21) to a torque
35 ± 4 N·m (26 ± 3 lb ft) . Install O-ring seal (20). Install plug (19). Tighten plug (19) to a torque17 ± 1.5 N·m (150 ± 13lb in) .Show/hide tableIllustration 2 g01344901 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install ball (15). Install spring (16). Install retainer (17). Install retaining ring (18).
- Install slug (14). Install spool (13).
Show/hide table
Illustration 3 g01344900 - Install spring (12). Install piston (11).
Show/hide table
Illustration 4 g01344896 - Install O-ring seal (10).
Show/hide table
Illustration 5 g01344891 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install screw (8) and cover (7) onto body (9). Install bolts (6). Tighten bolts (6) to a torque of
28 ± 7 N·m (21 ± 5 lb ft) .Show/hide tableIllustration 6 g01344888 - Install O-ring seal (5).
Show/hide table
Illustration 7 g01344871 - Install cover (4). Install bolts (3). Tighten bolts (3) to a torque of
28 ± 7 N·m (21 ± 5 lb ft) .Show/hide tableIllustration 8 g01344856 - Install O-ring seal (2). Install test port (1). Tighten test port (1) to a torque
17 ± 1.5 N·m (150 ± 13 lb in) .
Show/hide table
Illustration 1 | g01344905 |
End By:
- Install the relief valve.
Caterpillar Information System:
14L Motor Grader Relief Valve (Main) - Disassemble
Installation Guide for the PL1000E Communications ECM{7610} Installation Guide for the PL1000E Communications ECM{7610}
G3500 Engines Vibration Damper
G3520B Engines Vibration Damper
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Customer Communication Module
G3520B Engine Belts - Inspect/Adjust/Replace
3500B Engines Radiator Core - Install
A New Turbocharger is Now Available{1000, 1052, 5510} A New Turbocharger is Now Available{1000, 1052, 5510}
C13, C15, and C18 Tier 4 Final Engines Cylinder Liner
C3.3 Industrial Engine Cylinder Head - Inspect
2007/09/17 Maintenance Interval for the Crankcase Breather {1317}
2007/09/01 A Shorter Drive Belt for the Alternator on Bluebird Buses is Now Available {1207, 1397}
G3408C and G3412C Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
G3520B Engine Model View Illustrations
Reconditioning Dimensions for Idlers {4159} Reconditioning Dimensions for Idlers {4159}
TH31 Well Servicing Transmissions Transfer Gears - Disassemble
2007/09/24 Improved Software that Helps to Conserve Ether is Available {1901, 1902, 7620}
TH31 Well Servicing Transmissions Transfer Gears - Assemble
Installation Guide for the 256-7511 PL1000T Communication ECM{7606, 7610} Installation Guide for the 256-7511 PL1000T Communication ECM{7606, 7610}
2007/09/24 O-ring Aids in Engine Break-in {1251, 1290}
2007/09/01 O-ring Aids in Engine Break-in {1251, 1290}
2007/10/01 Matched Receiver Firmware for AccuGrade Dual GPS Systems {7010, 7620}
G3520B Engines Fuel Lines
2007/10/01 Improved Fuel Transfer Pump {1258, 1260}