1. Home
  2. Caterpillar
  3. Technical Analysis
  4. #i07605623

316F ExcavatorTA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} Caterpillar


316F ExcavatorTA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}

Usage:

316F L ECZ
Excavator
316F (S/N: XAD1-UP; YDL1-UP; ECZ1-UP)

Introduction

Inspections are the most basic form of condition monitoring. Inspections are easy to do and surprisingly effective at helping you spot equipment health issues. Proactive monitoring and analysis of equipment information will allow Dealers to intervene effectively before problems occur.

Note: Before adjusting product settings to comply with listed baseline TA2 values, consult SIS for the latest specification values.

Note: Specification values are based on the following machine settings unless stated otherwise

  • Engine Speed Dial "10"

  • AEC OFF

Creating an Electronic Copy

Use the following procedure to create an editable electronic copy from SIS Web.

  1. Click format to print.

  2. Save the document as an HTML format.

  3. Open the document with Microsoft Word.

Electrical System

Show/hide table
Table 1
Status(1)  Description  Specification  Actual  Comments 
  Inspect Battery Cables  Cables between the battery, the starter, and the engine ground must be the correct size. Wires and cables must be free of corrosion. Wires and cables must have cable support clamps in order to prevent stress on battery connections (terminals).     
  Battery Test(2)  12.4 VDC or more     
  Charging System Test(3)  18 VDC to 32 VDC     
  Electric Starting System Test(4)  12 to 16 V at −23° C (−10° F) to −7° C (19° F)     
14 to 18 V at −7° C (19° F) to 10° C (50° F)
16 to 24 V at 10° C (50° F) to 27° C (80° F)
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
(3) Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".
(4) Refer to Testing and Adjusting, RENR2415, "Electric Starting System - Test".

Engine

Cooling System

Show/hide table
Table 2
Status(1)  Description  Specification  Actual  Comments 
  Radiator Pressure Relief (Radiator Cap)(2)      Refer to System Operation Testing and Adjusting. 
  Freezing Point of Engine Coolant      Refer to Operation and Maintenance Manual. 
  Conditioner Test of Engine Coolant      Refer to Operation and Maintenance Manual. 
  Difference between the Upper and Lower Radiator Tank Temperatures       
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Test for the pressure that is listed on the cap.

Fuel System

Show/hide table
Table 3
Status(1)  Description  Specification  Actual  Comments 
  Fuel Pressure of the Low-Pressure Fuel System at Idle Speed  150 kPa (22 psi)     
  Maximum Fuel Pressure of the High-Pressure Fuel System  200 MPa (29000 psi)     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Lubrication System

Show/hide table
Table 4
Status(1)  Description  Specification  Actual  Comments 
  Minimum Engine Oil Pressure at Maximum Engine Speed  280 kPa (40 psi)     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Basic Engine

Show/hide table
Table 5
"Engine Performance - Test (Engine Speed)" 
Conditions  Specifications 
Status(1)  Engine  "AEC" Switch Position  "Engine Speed Dial" Position  Time (sec)  New  Service Limit  Actual  Comments 
  No load  OFF  10  0 to 5  1800 ± 50 rpm     
  OFF 10  > 5  1700 ± 50 rpm     
  ON 10  > 5  1150 ± 50 rpm     
  OFF 1  > 5  950 ± 50 rpm     
  One touch low idle > 0  1150 ± 50 rpm     
  Load(2)  OFF  10  > 3 to 5  1700 ± 50 rpm  ≥ 1650 rpm     
  Travel (3)  OFF  10  > 10  1875 ± 50 rpm     
  Travel (4)  OFF  10  > 10  2000 ± 50 rpm  ≥ 1950 rpm     
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) pump main relief (Boom UP).
(3) One track blocked
(4) Both tracks blocked

Air Inlet and Exhaust System

Show/hide table
Table 6
Status(1)  Description  Specification  Actual  Comments 
Inlet Manifold Pressure - Test 
  Cylinder # 1 Exhaust Temperature(2)       
  Cylinder # 2 Exhaust Temperature(2)       
  Cylinder # 3 Exhaust Temperature(2)       
  Cylinder # 4 Exhaust Temperature(2)       
  Cylinder # 5 Exhaust Temperature(2)       
  Cylinder # 6 Exhaust Temperature(2)       
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Compare the exhaust temperature variance at each exhaust port.

Performance Checks

Reference: Refer to Testing & Adjusting, UENR5625, "Performance Tests" for more detail on the following test.

Operational Checks

Travel on Level Ground - Test

Show/hide table
Table 7
"Travel on Level Ground - Test" 
Status(1)  Travel Speed  New  Service Limit  Actual  Comments 
Travel Time (time in seconds) 
  HIGH  Forward  13.7 ± 1.0  17.8 or less     
  Reverse  
  LOW  Forward  22.6 ± 1.5  29.4 or less     
  Reverse  
Travel Deviation(2) mm (inch) 
  HIGH  Forward  650 mm (25.6 inch) or less  1500 mm (59.1 inch) or less     
  Reverse  
  LOW  Forward 
  Reverse  
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Travel deviation (distance) from the reference line

Travel on Level Ground - Test (Optional Test)

Show/hide table
Table 8
"Travel on Level Ground - Test (Optional Test)" 
Time For Three Revolutions (time in seconds) 
Status(1)  Machine  Travel Speed  New  Service Limit  Actual  Comments 
Right Left
  Long  HIGH  Forward  17.2 ± 1.0  22.3 or less       
  Reverse  
  LOW Forward  28.4 ± 1.0  36.9 or less       
  Reverse  
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Automatic Travel Speed Control - Test

Show/hide table
Table 9
"Automatic Travel Speed Control - Test" 
Status(1)  Machine Settings  Engine Speed 
Engine Speed Dial "10"
AEC switch OFF
Blocked Track Pressure tap  Speed  Specification  Actual  Comments 
  Right Travel  Drive Pump  High to Low  32000 ± 500 kPa (4641 ± 73 psi)     
  Low to High 18000 ± 1500 kPa (2611 ± 218 psi)    
  Left Travel  Idler Pump  High to Low  32000 ± 500 kPa (4641 ± 73 psi)     
  Low to High 18000 ± 1500 kPa (2611 ± 218 psi)     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Machine Drift on a Slope - Check

Show/hide table
Table 10
"Machine Drift on a Slope - Check" 
Status(1)  Description  Specification  Actual  Comments 
New Service Limit
  Machine Drift  0 mm  0 mm     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Swing Speed and Overswing on Level Ground - Check

Show/hide table
Table 11
"Swing Speed and Overswing on Level Ground - Check" 
Status(1)  Description  New  Service Limit  Actual  Comments 
Overswing mm (inch) 
  Right Swing  850 mm (33.5 inch) or less  1300 mm (51.2 inch) or less     
  Left Swing 
Swing Time(2) (seconds) 
  Right Swing  4.7 or less  6.1 or less     
  Left Swing 
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) The time that is required to complete a 180 degree swing operation

Swing Speed and Swing Drift on a Slope -Check

Show/hide table
Table 12
"Swing Speed and Swing Drift on a Slope" 
Status(1)  Description  New  Service Limit  Actual  Comments 
Swing Time (seconds) 
  Right Swing  3.1 or less  4.3 or less     
  Left Swing 
Swing Drift mm (inch) 
  Right Swing  0  0     
  Left Swing 
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Cylinder Drift - Check (Loaded Bucket)

Show/hide table
Table 13
"Cylinder Drift - Check (Loaded Bucket)" 
Status(1)  Description  Cylinder Drift  New  Service Limit  Actual  Comments 
  Boom Cylinder  Retract  4.5 mm (0.18 inch) or less  24.0.0 mm (0.94 inch) or less     
  Stick Cylinder  Extend  12.0 mm (0.47 inch) or less  30.0 mm (1.18 inch) or less     
  Bucket Cylinder  Retract  18.0 mm (0.71 inch) or less  45.0 mm (1.77 inch) or less     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Cylinder Drift - Check (Empty Bucket)

Show/hide table
Table 14
"Cylinder Drift - Check (Empty Bucket)" 
Status(1)  Description  Cylinder Position  Drift Direction  New  Service Limit  Actual  Comments 
  Boom Cylinder  Retract  Boom Down  4.5 mm (0.18 inch) or less  11.0 mm (0.43 inch) or less     
  Stick Cylinder  Extend  Stick In  10.0 mm (0.39 inch) or less  25.0 mm (0.98 inch) or less     
  Retract Stick Out  25.0 mm (0.98 inch) or less  62.0 mm (2.44 inch) or less     
  Bucket Cylinder  Extend  Bucket Closed  20.0 mm (0.79 inch) or less  50.0 mm (1.97 inch) or less     
  Retract Bucket Open  10.0 mm (0.39 inch) or less  25.0 mm (0.98 inch) or less     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Cylinder Speed - Check

Show/hide table
Table 15
"Cylinder Speed - Check" 
Status(1)  Description  Cylinder Position  Cylinder Operating Speed (seconds) 
New Service Limit  Actual  Comments 
  Boom  Extension  3.1 ± 0.3  4.7     
  Retraction 1.8 ± 0.3  2.7     
  Stick  Extension  2.9 ± 0.3  4.4     
  Retraction 2.3 ± 0.3  3.5     
  Bucket  Extension  4.3 ± 0.3  6.5     
  Retraction 2.2 ± 0.3  3.3     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Pilot System

Reference: Refer to Testing & Adjusting, UENR5625 for more detail on the following tests.

Relief Valve (Pilot) - Test and Adjust

Show/hide table
Table 16
"Relief Valve (Pilot)- Test and Adjust" 
Status(1)  Machine Settings  Description  Specification  Actual  Comments 
  Speed Dial "10"
AEC switch OFF 		 Pilot relief valve pressure  4100 ± 200 kPa (595 ± 29 psi)     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Accumulator (Pilot) - Test and Charge

Show/hide table
Table 17
"Accumulator (Pilot) - Test" 
Status(1)  Description  Specification  Actual  Comments 
  Pilot Accumulator  1035 kPa (150 psi)    Should stay above 1035 kPa (150 psi) for 20 seconds 
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Power Shift Pressure - Check

Show/hide table
Table 18
"Power Shift Pressure - Check" 
Status(1)  Description  Machine Settings  Specification  Commanded(2)  Actual (3)  Comments 
  Power Shift Pressure
(No Load) 		 Speed Dial "10"
AEC switch OFF 		 3750 ± 250 kPa (544 ± 36 psi)       
  Power Shift Pressure
(Full Load) 		 1150 ± 300 kPa (167 ± 44 psi)      
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Value from the monitor
(3) Value from the pressure gauge

Main Control Valve

Reference: Refer to Testing & Adjusting, UENR5625 for more detail on the following tests.

Relief Valve (Main) - Test and Adjust

Show/hide table
Table 19
"Relief Valve (Main) - Test and Adjust" 
Status(1)  Description  Machine Settings  Specification  Actual  Comments 
  Main Relief  Implement  Speed Dial "10"
AEC switch OFF 		 35000 ± 500 kPa (5076 ± 72 psi)     
  Travel  
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Relief Valve (Line) - Test and Adjust

Show/hide table
Table 20
"Relief Valve (Line) - Test and Adjust" 
Status(1)  Cylinder  Cylinder Position  Machine Settings  Relief Pressure Setting  Actual  Comments 
  Boom  Extended  Speed Dial "10"
AEC switch OFF 		 37000 ± 500 kPa (5366 ± 73 psi)     
  Retracted  
  Stick  Extended 
  Retracted  
  Bucket  Extended  27500 ± 1000 kPa (3989 ± 145 psi)    
  Retracted 29900 ± 1000 kPa (4337 ± 145 psi)   
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Swing System

Reference: Refer to Testing & Adjusting, UENR5625 for more detail on the following tests.

Relief Valve (Swing) - Test and Adjust

Show/hide table
Table 21
"Relief Valve (Swing) - Test and Adjust" 
Status(1)  Description  Machine Settings  Specification  Actual  Comments 
  Right Swing(2)  Engine speed dial "10"
AEC switch OFF 		 24550 ± 1000 kPa (3561 ± 145 psi)     
  Left Swing(2) 
Show/hide table
(1) N = Normal, M = Monitor, A = Action
(2) Replace relief valve if pressure is not within specification.

Swing Bearing Movement - Measure

Show/hide table
Table 22
"Swing Bearing Movement - Measure" 
Status(1)  Description  Specification  Actual  Comments 
New Service Limit
  Vertical Movement of Swing Bearing  1.5 mm (0.06 inch)  3.0 mm (0.12 inch)     
  Circular Movement of Swing Bearing  4.0 mm (0.16 inch)  12.0 mm (0.47 inch)     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Travel System

Reference: Refer to Testing & Adjusting, UENR5625 for more detail on the following tests.

Relief Valve (Crossover) - Test

Show/hide table
Table 23
"Relief Valve (Crossover) - Test" 
  Machine Settings  Engine Speed  Main Relief Pressure(1) 
Engine speed dial "10"
AEC switch OFF 		Implement 35000 ± 500 kPa (5076 ± 73 psi)
Travel
Status(2)  Sales Model  Description  Direction  Service Limit(3)  Actual  Comments 
  316F (S/N: XAD20001-UP; YDL20026-UP; ECZ20005-UP)  Left Travel  Forward  36800 kPa (5337 psi)     
  Reverse  
  Right Travel Forward   
  Reverse  
Show/hide table
(1) System Pressure setting before temporary setting adjustment
(2) N = Normal, M = Monitor, A = Action
(3) Minimum

Relief Valve (Crossover) - Test and Adjust

Show/hide table
Table 24
"Relief Valve (Crossover) - Test and Adjust" 
  Machine Settings  Main Relief Pressure(1)  Engine Speed 
35000 ± 500 kPa (5076 ± 73 psi) Engine speed dial "10"
AEC switch OFF
Status(2)  Sales Model  Description  Direction  Specification  Actual  Comments 
  316F (S/N: XAD1-20000; YDL1-20025; ECZ1-20004)  Left Travel  Forward  37000 ± 1500 kPa (5366 ± 218 psi)     
  Reverse  
  Right Travel Forward   
  Reverse  
Show/hide table
(1) System Pressure setting before temporary setting adjustment
(2) N = Normal, M = Monitor, A = Action

S.O.S

Show/hide table
Table 25
Status(1)  Description  Obtain  Comments 
  Engine Oil Sample     
  Engine Coolant Sample (Level II)     
  Hydraulic Oil Sample     
  Swing Drive Oil Sample     
  Right Final Drive Oil Sample     
  Left Final Drive Oil Sample     
Show/hide table
(1) N = Normal, M = Monitor, A = Action

Caterpillar Information System:

314F and 315F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 314F and 315F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
312F GC and 313F GC Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 312F GC and 313F GC Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
312F and 313F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 312F and 313F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
352 UHD Excavator Belt - Inspect/Adjust/Replace
Pre-Delivery Instructions for Multiple Paving Machines Equipped With Certain Electronic Control Groups that Use PL631 {5267, 7606, 7620} Pre-Delivery Instructions for Multiple Paving Machines Equipped With Certain Electronic Control Groups that Use PL631 {5267, 7606, 7620}
New Diesel Exhaust Fluid (DEF) Pump Software and A New DEF Injector Is Available for Certain C4.4 Machine Engines {7620} New Diesel Exhaust Fluid (DEF) Pump Software and A New DEF Injector Is Available for Certain C4.4 Machine Engines {7620}
120 Motor Grader Monitoring System Machine Menu
Handle Control Gp may Fail on Certain Wheeled Excavators and Wheeled Material Handlers {5705} Handle Control Gp may Fail on Certain Wheeled Excavators and Wheeled Material Handlers {5705}
330F Excavators Machine System Specifications Diesel Exhaust Fluid Lines
New Monitor Software is Now Available for Certain 700 Series Articulated Trucks {7490, 7610, 7620} New Monitor Software is Now Available for Certain 700 Series Articulated Trucks {7490, 7610, 7620}
R2900 Load Haul Dump Tire Shipping Pressure
R2900 Load Haul Dump General Information (Remote Control) - If Equipped
318F ExcavatorTA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} 318F ExcavatorTA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}
320F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 320F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
323F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 323F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
325F Excavator TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} 325F Excavator TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}
C9.3 Tier 4 Final Engines Oil Consumption Is Excessive
329F and 330F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 329F and 330F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
335F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 335F Excavator TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
349 and 352 Excavator Systems Accumulator (Pilot)
349 and 352 Excavator Systems General Information (Pilot System)
349 and 352 Excavator Systems General Information (Swing System)
349 and 352 Excavator Systems Swing System
349 and 352 Excavator Systems Relief Valve (Swing)
Back to top
Contacts My AVS
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.