2003/09/15 Caterpillar


An Improved Alternator Belt is Used {1357}

Usage:

793B 1HL
Caterpillar Products: Machine Engines
  • All 3500 Series
  • Service Magazine, SEPD0700, 15 September 2003, "An Improved Alternator Belt is Used". Disregard this article. The value for belt tension should be given in units of force. Refer to the following article.

    Description of Change: An new alternator belt is being introduced for use in all 3500 Machine Engines. The new alternator belt is constructed of a material that has a proven resistance to fatigue. The new alternator belt also has a higher temperature rating.

    Adaptable To: The 141-7116 Belt is a direct replacement for the 7E-4841 Serpentine Belt, which is being discontinued in August 2003. The 141-7116 Belt is currently used on 992G Wheel Loaders. In August 2003, the new alternator belt will be used on all of the above products. The new alternator belt has the same dimensions as the previous alternator belt.

    Belt Tension is Critical to the Service Life of Alternator Belts

    To obtain the maximum service life of the alternator belt and of the pulleys, the correct belt tension is critical. If the tension is inadequate, the belt may roll on the pulley or the belt may slip. The slipping will reduce the service life of the belt. If the tension is excessive, the extra tension on the belt and on the pulleys will reduce the service life of the parts.

    Tension for the 141-7116 Belt

    Tension for a new belt ... 800 N (180 lb)
    Tension for a used belt ... 489 N (110 lb)

    When you install a new belt, adjust the belt to the correct tension. Then, operate the engine for a minimum of 30 minutes at the full load rpm (rated speed) that is stamped on the engine information plate.

    A belt is considered to be used after at least 30 minutes of use at the rated speed. After a minimum of 30 minutes of operation at the rated speed, stop the engine and adjust the tension to the specification for a used belt.

    The new 240-8220 Belt Tension Gauge Gp is recommended for tensioning of the belt.

    A New Belt Tension Gauge is Available

    The new 240-8220 Belt Tension Gauge Gp is now available. The gauge is for use with belts that have eight ribs. The gauge will work with belts that have a top width in the range of 9.65 to 31.75 mm (0.380 to 1.250 inch). The gauge has a working range of 445 to 890 N (100 to 200 lb).

    Caterpillar Information System:

    M325D MH Material Handler Window Washer Reservoir - Fill
    315C Excavator Machine Systems Boom Cylinder - Remove and Install
    345B Excavator Hydraulic System Counterweight (Removal and Installation Hydraulic System)
    2003/08/18 A New Egress Ladder is Used {7254, 7255}
    315C Excavator Machine Systems Stick Cylinder - Remove and Install
    321C LCR Excavator Machine Systems Pilot Valve (Joystick) - Install
    321C LCR Excavator Machine Systems Pilot Valve (Joystick) - Remove
    321C LCR Excavator Machine Systems Pilot Valve (Travel) - Install
    321C LCR Excavator Machine Systems Pilot Valve (Travel) - Remove
    M325C Material Handler Final Drive Oil - Change
    321C LCR Excavator Machine Systems Boom Lighting - Remove and Install
    M325C Material Handler Operation Information
    2003/10/01 An Improved Alternator Belt is Used {1357}
    321C LCR Excavator Machine Systems Swivel - Remove
    321C LCR Excavator Machine Systems Swivel - Install
    SW45 and SW60 Wheel Saws Frame (Rear) - Remove and Install
    Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458} Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458}
    321C LCR Excavator Machine Systems Cab - Remove
    321C LCR Excavator Machine Systems Cab - Install
    SW45 and SW60 Wheel Saws Check Valve - Remove and Install
    2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
    321C LCR Excavator Machine Systems Undercarriage Frame - Remove
    321C LCR Excavator Machine Systems Undercarriage Frame - Install
    2003/11/24 Remanufactured Improved Travel Motors With Increased Service Life Are Now Available {5058}
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.