Hydraulic System Oil Filter (Case Drain) - Replace - Wheel Brakes and Lower Manifold
Show/hide table
 | |
| Illustration 1 | g00750017 |
The hydraulic filter for the wheel brakes and the lower manifold is located on the side of the fuel tank. | |
Show/hide table
 | |
| Illustration 2 | g00752054 |
(1) Pressure gauge (2) Case drain filter | |
- Check pressure gauge (1). If the needle on the pressure gauge is in the red portion of the gauge, filter (2) should be replaced.
- Clean the area in order to keep dirt out of the filter base.
- Remove used hydraulic filter (2) from the filter base.
Note: This element is a cartridge type filter. The element cannot be reused.
Note: Dispose of used filters according to local regulations.
- Clean the filter base.
- Coat the seal of a new hydraulic filter with clean hydraulic oil. Install the new hydraulic filter in the filter base. Tighten the hydraulic filter hand tight.
Show/hide table
 | |
| Illustration 3 | g00101502 |
- Drive the machine slowly for 10 to 15 minutes. Shift the transmission and apply the brakes several times.
- Return the machine to the position that is shown above. Check the machine for oil leaks.
Show/hide table
 | |
| Illustration 4 | g00734775 |
- Stop the engine.
- Open the access door on the right side of the machine in order to access the sight gauge.
- Maintain the oil level in the low temperature range for a cold machine. Maintain the oil level in the high temperature range for a machine that is at a normal operating temperature.
Show/hide table
 | |
| Illustration 5 | g00101511 |
(A) High Temperature Range. (B) Low Temperature Range. | |
- Slowly loosen the filler plug in order to relieve any pressure. Remove the filler plug in order to add oil, if necessary.
Show/hide table
 | |
| Illustration 6 | g00101541 |
- Clean the filler plug. Install the filler plug.
- Close the access door.
Caterpillar Information System:
325C and 325C L Excavator Fuel System Primary Filter (Water Separator) Element - Replace
320C Excavator Specifications
3406E and 3456 Engines for Caterpillar Built Machines Engine Support (Front)
M325B Material Handler Power Train Travel Motor - Remove
320C Excavator Storage Box
325C and 325C L Excavator Fuel System Water Separator - Drain
307B Excavator VA Boom Controls
322C Excavator Fuel System - Prime
315C Excavator Cab Visor - If Equipped
5110B Excavator Bucket Linkage - Inspect/Adjust
2000/10/30 The Spring Seat Washer Is Now A Serviceable Component Of The Rocker Arm Cover Base Assembly {1102}
2000/11/06 Correction of the Disassembly and Assembly Manual for the Installation of the Main Hydraulic Pump and Pump Drive Coupling {5062, 5070}
307B, 312B, 315B, 317B and 318B Excavators Working Ranges
3406E and 3456 Engines for Caterpillar Built Machines Electric Starting Motor
M325B Material Handler Power Train Transmission - Remove
3406E and 3456 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
S305, S320, S325, S340, S365 and S390 Demolition and Scrap Shears Specifications
307C Excavator Hydraulic System Main Hydraulic System
307C Excavator Hydraulic System Pump Control (Main Hydraulic)
307C Excavator Hydraulic System Main Control Valve
307C Excavator Hydraulic System Main Control Valve
307C Excavator Hydraulic System Relief Valve (Main)
307C Excavator Hydraulic System Check Valve (Load)
307C Excavator Hydraulic System Pilot Hydraulic System