Idlers (Track)
Show/hide table
| |
| Illustration 1 | g06363906 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 1 | 7H-7131 Pipe Plug | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
| 2 | 2 | 482-9627 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Prior to assembly, apply a thin film of 095-1662 Lubricant to the contacting surfaces of the metal seal rings. The metal seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist. |
| D1 | - | - | Clearance between bearing and idler is |
| 3 | - | - | Prior to assembly, clean the surface to remove the protective coating. |
| D2 | - | - | Specified range is 40 degrees. |
| D3 | - | - | Angle from centerline of idler shaft is 20 degrees. |
| 4 | 2 | 099-0163 Pin | Install the pin with the slit in the range that is specified. The correct position of the pin is shown in view B-B. |
| 5 | 1 | 566-8474 Idler Shaft | Install the idler shaft. Position the "R" that is stamped on the end face of the idler shaft backward into the front idler bearing. |
| - | - | - | End play in axial direction:
Minimum is Maximum is |
Caterpillar Information System:
Transmission Filter Serviceability is Improved on Certain 793D Off-Highway Trucks {1374, 1380, 5057} Transmission Filter Serviceability is Improved on Certain 793D Off-Highway Trucks {1374, 1380, 5057}
Procedure to Improve Transmission Filter Serviceability on Certain 793D Off-Highway Trucks {1374, 1380, 5057} Procedure to Improve Transmission Filter Serviceability on Certain 793D Off-Highway Trucks {1374, 1380, 5057}
Improved Front Suspension Cylinder Bellows and Retention Clamps for 794 AC Off-Highway Trucks are Available {7201} Improved Front Suspension Cylinder Bellows and Retention Clamps for 794 AC Off-Highway Trucks are Available {7201}
Driver Safety System DSS Mining Test Button
Driver Safety System DSS Mining Speaker
Driver Safety System DSS Mining Camera
Band Clamps for Water Lines Are Breaking on Certain C18 Engines {1380} Band Clamps for Water Lines Are Breaking on Certain C18 Engines {1380}
Driver Safety System DSS Mining IR Light
Driver Safety System DSS Mining GPS Module
Service Tools Are Now Available for Certain Utility Vehicles {0599} Service Tools Are Now Available for Certain Utility Vehicles {0599}
Transmission Forward and Reverse Lever Troubleshooting Problem May Occur On Certain Backhoe Loaders {1408, 3168} Transmission Forward and Reverse Lever Troubleshooting Problem May Occur On Certain Backhoe Loaders {1408, 3168}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Solenoid Valve
High Voltage Cable Assembly Routing is Now Improved on Certain 794 AC Off-Highway Trucks {1408} High Voltage Cable Assembly Routing is Now Improved on Certain 794 AC Off-Highway Trucks {1408}
An Improved Harness Assembly is Now Used in the Transmission Wiring Group on Certain 777E, 777F, and 777G Off-Highway Trucks {1408, 3030} An Improved Harness Assembly is Now Used in the Transmission Wiring Group on Certain 777E, 777F, and 777G Off-Highway Trucks {1408, 3030}
Rework Procedure for the Fuel Filter Housing on Certain Machine Engines {1261} Rework Procedure for the Fuel Filter Housing on Certain Machine Engines {1261}
Procedure to Modify the Oil Pan for Additional Oil Sensor Ports on Certain 793F, 794AC, and 795F AC Off-Highway Truck Engines {1302, 1408, 1439, 7422} Procedure to Modify the Oil Pan for Additional Oil Sensor Ports on Certain 793F, 794AC, and 795F AC Off-Highway Truck Engines {1302, 1408, 1439, 7422}
14M Series 3 Motor Grader Circle Drive Pinion Teeth - Lubricate
The Implement Valve Tilt or Lift Section Centering Spring May Break on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {5051} The Implement Valve Tilt or Lift Section Centering Spring May Break on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {5051}
Manufacturing Process for the Standard Shift Transmission Synchronizer Sleeve Has Been Improved on Certain Backhoe Loaders {3030, 3053, 3063} Manufacturing Process for the Standard Shift Transmission Synchronizer Sleeve Has Been Improved on Certain Backhoe Loaders {3030, 3053, 3063}
The Final Drive Group has been Improved on Certain 777F and 777G Off-Highway Trucks {4050} The Final Drive Group has been Improved on Certain 777F and 777G Off-Highway Trucks {4050}
Hood or Right-hand Insulation may be Damaged on Certain F and F2 Series Backhoe Loaders {7150, 7170, 7251, 7263} Hood or Right-hand Insulation may be Damaged on Certain F and F2 Series Backhoe Loaders {7150, 7170, 7251, 7263}
Updated Cylinder Block Rear Housing Gasket is Now Available for Certain Cat® Machine Engines {1157, 1201} Updated Cylinder Block Rear Housing Gasket is Now Available for Certain Cat® Machine Engines {1157, 1201}
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Electrical Component and Connector Locations
Certain Cat® Product Link PL542 Devices May Take Longer Time Than Expected To Complete Registration {7606} Certain Cat® Product Link PL542 Devices May Take Longer Time Than Expected To Complete Registration {7606}