Engine Oil Filter Base - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 2P-8250 | Strap Wrench Assembly | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Use Tool (A) and remove oil filter (1) .
Show/hide table
 | |
| Illustration 1 | g00467095 |
- Disconnect hose assembly (2) . Remove bolt (4) and the washer. Disconnect the clip from the tube assembly. Remove bolt (8) , the washer and the spacer. Disconnect the clip from tube assembly (6) . Remove bolt (7) and the washer in order to disconnect tube assembly (5) and the washers. Remove engine oil filter base (3) , tube assemblies (5) and (6) and the gaskets.
Show/hide table
 | |
| Illustration 2 | g00467627 |
- Remove tube assemblies (5) and (6) from engine oil filter base (3) .
- Remove the two O-ring seals from the top of the engine oil filter base, if necessary.
- Check the condition of the gaskets and the O-ring seals. If the gaskets or the seals are worn or damaged, use new parts for replacement.
Caterpillar Information System:
3126 Truck Engine (Military) Commercial Heavy-Duty Coolant/Antifreeze and SCA
3600 Distillate Fuel Engines Refill Capacities
3126E and 3126B Commercial and Truck Engines Cooling System Supplemental Coolant Additive (SCA) - Test/Add
3208 Marine Engine Oil Fumes Filter - Replace
3126 Truck Engine (Military) Coolant Recommendations
3304B and 3306B Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
3304B and 3306B Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
P16, P20, P25, P28, P40 and P60 Pulverizer Safety Messages
3208 Marine Engine Sea Water Strainer - Clean/Inspect
C-18 Truck Engines Reference Material
Air Conditioning and Heating R134a for All Caterpillar Machines Manifold Gauge Set (Refrigerant) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Fuel Ratio Control - Assemble
P16, P20, P25, P28, P40 and P60 Pulverizer Bushing (Crushing Arm) - Lubricate
3208 Marine Engine Governor Housing - Drain
P16, P20, P25, P28, P40 and P60 Pulverizer Plate Locations and Film Locations
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Description
3208 Marine Engine Fuel System Secondary Filter - Replace
3208 Marine Engine Engine Oil Level - Check
P16, P20, P25, P28, P40 and P60 Pulverizer Ring Gear - Lubricate
3208 Marine Engine Fuel Ratio Control - Inspect/Adjust
3208 Marine Engine Fuel System Water Separator - Drain
Installation Of The Hydraulic Actuator System (Hydrax System) on G3606 and G3608 Engines {1050, 1250, 1908, 1915} Installation Of The Hydraulic Actuator System (Hydrax System) on G3606 and G3608 Engines {1050, 1250, 1908, 1915}
P16, P20, P25, P28, P40 and P60 Pulverizer Operating Technique Information
3406E, C-10, C-12, C-15, C-16 Truck Engines Starting the Engine