SE60 VT Asphalt Screed TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
- Asphalt Screed
- SE60VT XW (S/N: TLW1-UP)
Introduction
Inspections are the most basic form of condition monitoring. Inspections are easy to do and surprisingly effective at helping you spot equipment health issues. Proactive monitoring and analysis of equipment information will allow Dealers to intervene effectively before problems occur.
Note: Before adjusting product settings to comply with listed baseline TA2 values, consult SIS for the latest specification values.
Creating an Electronic Copy
Use the following procedure to create an editable electronic copy from SIS Web.
- Click format to print.
- Save the document as an HTML format.
- Open the document with Microsoft Word.
Screed Plate Check and Adjust
Reference: Refer to Testing & Adjusting, UENR3150 for more detail on the following test.
Show/hide table
| Status(1) | Description | Specification | Actual | Comments |
|---|---|---|---|---|
| The distance between drop arm face and slope box face | |
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
Tamper Bar Check and Adjust
Reference: Refer to Testing & Adjusting, UENR3150 for more detail on the following test.
Show/hide table
| Status(1) | Description | Specification | Actual | Comments |
|---|---|---|---|---|
| Correct distance between the bottom edge of the tamper blade and the bottom edge of the screed plate | |
|||
| Correct gap between the tamper blade and the tamper front guard | |
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
Extender Check and Adjust
Reference: Refer to Testing & Adjusting, UENR3150 for more detail on the following test.
Show/hide table
| Status(1) | Description | Specification | Actual | Comments |
|---|---|---|---|---|
| Correct angle of attack | |
|||
| Height adjustment chain deflection | |
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
Chain (Crown) Check and Adjust
Reference: Refer to Testing & Adjusting, UENR3150 for more detail on the following test.
Show/hide table
| Status(1) | Description | Specification | Actual | Comments |
|---|---|---|---|---|
| Crown chain maximum deflection | |
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
Heater Element Test
Reference: Refer to Testing & Adjusting, UENR3150 for more detail on the following test.
Show/hide table
| Status(1) | Description | Specification | Actual | Comments |
|---|---|---|---|---|
| Resistance across pin "A" and pin "B" in the screed plate heater element harness | 143.6 ohms to 167.2 ohms | |||
| Resistance across pin "A" and pin "B" in the end gate heater element harness | 76.9 ohms to 89.6 ohms | |||
| Amount of allowable insulation leakage across pin "A" and pin "C" in heater element harness | The resistance should be greater than five mega-ohms at room temperature | |||
| Amount of allowable insulation leakage across pin "B" and pin "C" in heater element harness | The resistance should be greater than five mega-ohms at room temperature | |||
| Resistance across pin "A" and pin "B" in heater element to screed junction box harness | Five mega-ohms | |||
| Amount of allowable insulation leakage across pin "A" and pin "C" in heater element to screed junction box harness | The resistance should be greater than five mega-ohms at room temperature | |||
| Amount of allowable insulation leakage across pin "B" and pin "C" in heater element to screed junction box harness | The resistance should be greater than five mega-ohms at room temperature | |||
| Harness connector torque | |
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
S·O·S Samples
Reference: Refer to Operation and Maintenance Manual, KEBU7063, "Maintenance Interval Schedule" for more detail on performing S.0.S samples.
Show/hide table
| Status(1) | Description | Obtain | Comments | |
|---|---|---|---|---|
| Hydraulic System Oil Sample | ||||
| Pump Drive Oil Sample | ||||
| Right Final Drive Planetary Oil Sample | ||||
| Left Final Drive Planetary Oil Sample | ||||
| Right Conveyor Planetary Drive (Auger) Oil Sample | ||||
| Left Conveyor Planetary Drive (Auger) Oil Sample | ||||
| Right Conveyor Planetary Drive (Drag) Oil Sample | ||||
| Left Conveyor Planetary Drive (Drag) Oil Sample | ||||
Show/hide table
| (1) | N = Normal, M = Monitor, A = Action |
Caterpillar Information System:
Improved Front Axle Brake Cooling Manifold and Brake Cooling Tubes are Now Used on Certain 700 C-Series Articulated Trucks {1374, 4257} Improved Front Axle Brake Cooling Manifold and Brake Cooling Tubes are Now Used on Certain 700 C-Series Articulated Trucks {1374, 4257}
New Improved Control Valves Are Used on Certain 24H Motor Graders {5051} New Improved Control Valves Are Used on Certain 24H Motor Graders {5051}
PM310, PM312, and PM313 Cold Planers Electronic System ECM Software - Install
SE60 V Asphalt Screed TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} SE60 V Asphalt Screed TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
PM310, PM312, and PM313 Cold Planers Electronic System Wiring Harness (Short Circuit) - Test
PM310, PM312, and PM313 Cold Planers Electronic System Wiring Harness (Open Circuit) - Test
PM310, PM312, and PM313 Cold Planers Electronic System Speed Sensor - Test
PM310, PM312, and PM313 Cold Planers Electronic System Solenoid Valve - Test
CD8 Asphalt Compactor Propel Systems Piston Pump Neutral (Mechanical) - Test and Adjust - Split Drum
C7.1 Industrial Engine Electronic Control Module
PM310, PM312, and PM313 Cold Planers Electronic System Solenoid Return - Test
PM310, PM312, and PM313 Cold Planers Electronic System Sensor Supply - Test
PM310, PM312, and PM313 Cold Planers Electronic System ECM - Configure
PM310, PM312, and PM313 Cold Planers Electronic System ECM - Replace
PM310, PM312, and PM313 Cold Planers Electronic System Connector Contact Description
CW16 Pneumatic Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} CW16 Pneumatic Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
CD8 Asphalt Compactor Propel Systems Piston Pump Neutral - Test and Adjust - Electronic Displacement Control, Split Drum
CCS7 Vibratory Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} CCS7 Vibratory Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
487-8629 C175 Harmonic Engine Damper Lifting Device and 487-8630 Damper Guide Pin Assembly {0374, 0629, 0632, 0701, 1205, 5569} 487-8629 C175 Harmonic Engine Damper Lifting Device and 487-8630 Damper Guide Pin Assembly {0374, 0629, 0632, 0701, 1205, 5569}
CCS9 Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} CCS9 Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
M0080739 High Pressure Fuel Pump (HPFP) 487-8643 Lifting Device {0629, 0700, 125H} M0080739 High Pressure Fuel Pump (HPFP) 487-8643 Lifting Device {0629, 0700, 125H}
CB7, CB8, and CB10 Compactors TA2 Technical Inspection {0372, 1000, 7000, 7533, 753T, 7565} CB7, CB8, and CB10 Compactors TA2 Technical Inspection {0372, 1000, 7000, 7533, 753T, 7565}
Ball Stud Breaker (524-9370 Hammer Group) {0374, 0599, 0700, 0732, 0738} Ball Stud Breaker (524-9370 Hammer Group) {0374, 0599, 0700, 0732, 0738}
CD8 and CD10 Asphalt Compactor and Vibratory Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} CD8 and CD10 Asphalt Compactor and Vibratory Asphalt Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}