735C and 745C Articulated Trucks Machine Systems Caterpillar


System Pressure - Release

Usage:

735C LFJ

------ WARNING! ------

增压系统!

液压蓄能器含有高压气体和机油。 请勿断开管路或拆解加压蓄能器的任何部件。 维修蓄能器或任何蓄能器部件前,应按照维修手册的说明从蓄能器中清除预充气体。

不遵循这些说明和警告会造成人身伤亡。

只能使用干燥的氮气加注蓄能器。 有关特殊设备和蓄能器维修和充注的详细信息,请咨询您的 Cat 代理商。


------ WARNING! ------

高压缸。 解体过程中如果不加注意,零件就有可能因爆发的力而飞出。

这可能造成人身伤亡。

在阅读并理解维修手册中所给出的说明之前,不要解体该缸中的任何零部件。 阅读维修手册中所给出的说明。


------ WARNING! ------

在发动机停机后,液压系统或动力传动系的部件中将会依然存在高压下的热液压油。 液压油的未受控制的释放可能会导致机器的突然移动或造成以下情况:

  • 烧伤

  • 穿透人体组织

  • 其他人身伤害

  • 死亡

如果液压油穿透人体组织,必须立刻找熟悉这类创伤的医生来治疗。 请使用木板或硬纸板來检查液压油泄漏情况。 确保所有附件都已经降至地面上并且液压系统和动力传动系中的所有截留的压力都已经得到了释放。 此外,在拆卸任何部件或管路前,要确保液压油是冷的。 只有当发动机停机,而且加注口盖足够冷却,可以直接用手接触时,才可以拆卸液压油加注口盖。



注意

在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

按照当地法规和要求处置所有液体。


机器准备

  1. 将机器放在光滑、水平的表面上。 位置应该干燥并没有碎屑。 停止发动机。

  1. 机器上仅允许停留一位操作员。 应保持所有其他人员远离机器。

  1. 接合停车制动器。

释放系统压力

  1. 起动发动机并完全缩回推料器铲刀。 将推料器操纵杆移到保持位置。

  1. 关闭发动机,然后将发动机起动开关转至接通位置。

  1. 接合行车制动器数次,直到释放行车制动器系统油中的全部压力。

  1. 将停车制动器控制器在接合位置和脱开位置之间移动。 重复该步骤数次,直到释放停车制动器系统油中的全部压力。

  1. 将发动机起动开关转到断开位置。

  1. 顺时针转动方向盘。 逆时针转动方向盘。

  1. 小心地拆卸推料器和制动系统液压油箱的加注口盖。 拆下盖将释放液压油箱中的全部压力。

  1. 小心地拆卸转向和风扇驱动系统液压油箱的加注口盖。 拆下盖将释放液压油箱中的压力。

  1. 安装加注口盖。

Caterpillar Information System:

2015/01/23 Instructions to Disable Compatibility Mode For CAESoffice Executable On Windows 7 Operating Systems {7490, 7600, 7605}
299D2 and 299D2 XHP Compact Track Loaders, 297D2 and 297D2 XHP Multi Terrain Loaders and 272D2 and 272D2 XHP Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Remove and Install - Standard Flow
735C and 745C Articulated Trucks Machine Systems Machine Preparation for Testing and Adjusting
CP34 and CS34 Vibratory Soil Compactors Engine Oil and Filter - Change
CP34 and CS34 Vibratory Soil Compactors Engine Oil Sample - Obtain
735C and 745C Articulated Trucks Belt - Inspect/Replace
Incorrect Torque Specifications in the Operation and Maintenance Manual, "Wheel Nut Torque - Check" for F-Series Backhoe Loaders{4057, 4201, 4202, 4208, 4209} Incorrect Torque Specifications in the Operation and Maintenance Manual, "Wheel Nut Torque - Check" for F-Series Backhoe Loaders{4057, 4201, 4202, 4208, 4209}
PL72 Pipelayer Winch Oil Level - Check
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train NoSPIN Differential - Test - Before Installation
PL72 Pipelayer Winch Oil - Change
F2 Series Backhoe Loaders Monitoring System Service Menu
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Transmission (Power Shift) - Install
2015/01/27 Uninstalling Updates and Disabling Automatic Windows Updates Enables "B" Snippets Within METSmanager {7604}
735C and 745C Articulated Trucks Machine Systems Hydraulic Oil Contamination - Test
745 Articulated Truck Fuel System - Prime
2014/12/17 Improved LARN Antenna Now Used on CAT ® Command for Underground Equipped Machines {7338, 733T}
745 Articulated Truck Brake Tank Strainer - Clean/Inspect/Replace
415F2, 416F2, 420F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Hydraulic and Steering System Steering Control
415F2, 416F2, 420F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Hydraulic and Steering System Bucket Cylinder (Backhoe)
Visual Routing Guide for Battery Cable and Fuel Lines for Certain 24M Motor Graders{1408} Visual Routing Guide for Battery Cable and Fuel Lines for Certain 24M Motor Graders{1408}
415F2, 416F2, 420F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Axles, Differential and Brakes Service Brake Control
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Hydraulic and Steering System Hydraulic Hand Control
422F2, 426F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Axles, Differential and Brakes Service Brake Control
422F2, 427F2, 428F2, 432F2 and 434F2 Backhoe Loaders Transmission (Standard Shift) Transmission (Standard Shift)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.