Final Drive, Brake, and Wheel
Show/hide table
Illustration 1 | g03730803 |
Left side view |
Show/hide table
Illustration 2 | g03730895 |
Right side view |
Show/hide table
Illustration 3 | g03730804 |
View of Section A-A |
Show/hide table
Item | Qty | Part | Specification Description |
1 | 10 | 1D-4610 Bolt | Install bolts and tighten to |
2 | 4 | 2J-3507 Full Nut | Torque to |
3 | - | - | Mounting surfaces to be free of paint and grease prior to assembly. |
4 | 8 | 0S-1591 Bolt | Torque to |
5 | - | - | Mounting surfaces to be free of paint and grease prior to assembly. |
6 | 1 | 314-4126 Duo-Cone Seal Gp | Rubber toric rings and all surfaces contacting the rubber toric rings must be clean and dry at assembly. Apply a think film of oil to contacting surfaces of the metal seals prior to the assembly. The seal rings must be assembled square with the bore and toric must not be bulged or twisted. |
7 | 1 | 6V-6638 O-Ring Seal | Lubricate lightly with the lubricant being sealed |
8 | 1 | 6G-9079 Shim Pack | Total shim thickness is The following wheel bearing setting procedure may be performed with or without the brake group installed and with or without the duo-cone seals installed. If the brake group is installed, the parking brake must be released. Make sure that the bearing cups are fully seated against the bore backfaces in the wheel and the outer bearing cone slides freely over the spindle. The bolts should be tightened in a crossing pattern at each step. To obtain the wheel bearing preload with a vertical assembly of parts only, install the retainer with five new bolts, equally spaced. Tighten the bolts to |
9 | 1 | 422-9075 Duo-Cone Seal Gp | Rubber toric rings and all surfaces contacting the rubber toric rings must be clean and dry at assembly. Apply a think film of oil to contacting surfaces of the metal seals prior to the assembly. The seal rings must be assembled square with the bore and toric must not be bulged or twisted. |
10 | - | - | Mounting surfaces to be free of paint and grease prior to assembly. |
11 | 68 | 2J-3505 Full Nut | Torque to |
12 | 1 | 205-9874 Speed Sensor Gp | Seal the sensor threads with Loctite 536.
Torque to |
13 | 1 | 5T-8041 Adapter | Seal the threads with Loctite 536.
Torque to |
14 | 2 | 5T-8169 Shim | Use as required to obtain dimension.
Shim thickness |
15 | 3 | 5T-8168 Shim | Use as required to obtain dimension.
Shim thickness |
16 | 2 | 5T-8042 Shim | Use as required to obtain dimension.
Shim thickness |
Caterpillar Information System:
AP655F and AP655F L Asphalt Paver Machine Systems Screed Frame
785G Off-Highway Truck Systems Brake Valve (Front Service Brake)
725C2 and 730C2 Articulated Truck Machine System Front Frame and Rear Frame - Separate
428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Specifications
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Brake Control Valve (Parking) - Remove and Install
C3.4B Engines Relay - Test - Start Relay
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge
Installation of the 466-1959 Kit for Closed Crankcase Breather (CCB) On Certain Machines Equipped with C3.3B Tier 4 Final Engines {1317} Installation of the 466-1959 Kit for Closed Crankcase Breather (CCB) On Certain Machines Equipped with C3.3B Tier 4 Final Engines {1317}
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Brake Control Valve (Parking) - Remove and Install
2014/10/01 An Improved Air Lines Group Is Now Available on Certain 14M Motor Graders {1071}
2014/10/15 Improved Lubrication Lines Group Is Now Used on 14M Motor Graders {7510}
428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Rated Load
PL83 and PL87 Pipelayers Air Conditioner Condenser - Clean - If Equipped
785G Off-Highway Truck Systems Brake Valve (Front Service Brake)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Bulldozer Stabilizer - Remove and Install
785G Off-Highway Truck Systems Brake Valve (Rear Service Brake)
Instructions for Installing Cab Storage Compartments on Certain M, M Series 2 and M Series 3 Motor Graders{7266, 7301, 7329} Instructions for Installing Cab Storage Compartments on Certain M, M Series 2 and M Series 3 Motor Graders{7266, 7301, 7329}
2014/09/29 The Multipurpose Bucket Cylinder Has Been Improved for Certain F Series Backhoe Loaders {5457, 6104}
PL83 and PL87 Pipelayers Engine Oil Level - Check
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump (Implement) - Test and Adjust
2014/12/09 Maintenance Parts for the Automatic Lubrication Group are Now Available for Certain Off-Highway Trucks {7516, 7540}
558 Forest Machine Maintenance Interval Schedule
785G Off-Highway Truck Systems Slack Adjuster (Front Brakes)
2014/09/30 New Transmission Software is Now Used on Certain 793F and 797F Off-Highway Trucks {3175, 7620}