Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Gp | 1 |
B | - | Loctite 620 Retaining Compound - Slip Fit/High Temp | 1 |
Note: Cleanliness is an important factor. Clean all parts thoroughly in cleaning fluid before assembly. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install inner seal (26) with the flat portion of inner seal (26) toward the bottom of the groove in piston housing (13).
- Install outer seal (25) with the flat portion of outer seal (25) toward the bottom of the groove in piston housing (13).
- Lubricate inner seal (26) and outer seal (25) with the lubricant that is being sealed.
Show/hide table
Illustration 3 g03693316 - Lubricate piston (22) with the lubricant that is being sealed. Install piston (22) into piston housing (13).
Show/hide table
Illustration 4 g03693343 - Install O-ring seal (21) to piston housing (13).
Show/hide table
Illustration 5 g03692417 Show/hide tableIllustration 6 g03693352 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install spring guides (15) and springs (16) to piston housing (13).
- Use Tooling (A) and a suitable press in order to compress springs (16).
- Install retaining pins (14) (not shown) into spring guides (15).
Note: Steps 9 through 12 are for the installation of the service brake wear indicator.
Note: The service brake wear indicator must be installed into the correct location of the brake piston. If the service brake wear indicator was removed, use Steps 9 through 12 in order to install the service brake wear indicator correctly .
Show/hide tableIllustration 7 g01110882 Hollow dowel locations. The current view shows the hollow dowel in the "RF/LR" location. - Locate the correct position in order to install the service brake wear indicator. The piston housing has identification marks that indicate the placement of the wear indicator pin. The indication marks are "RF/LR" and "LF/RR". Install the indicator pin in the appropriate location.
"RF/LR" - The identification mark on the piston housing for the installation in the right front service brake or installation in the left rear service brake.
"LF/RR" - The identification mark on the piston housing for the installation in the left front service brake or installation in the right rear service brake.
Show/hide tableIllustration 8 g03693462 Back Face of Piston
(17) Retaining Ring
(18) Hard Washer
(19) Wear Indicator Pin
(27) Identification Mark - Place hard washer (18) on the head of wear indicator pin (19). Install retaining ring (17) in order to hold wear indicator pin (19) and hard washer (18) to the piston.
Show/hide table
Illustration 9 g03693497 Show/hide tableIllustration 10 g03693506 End view of the piston housing portion of the service brake. Show/hide tableIllustration 11 g03693447 Service Brake Wear Indicator
(13) Piston Housing
(19) Wear Indicator Pin
(20) Hollow Dowel
(22) Piston
(B) Visible Length of the Wear Indicator Pin - Apply Tooling (B) to the threads of hollow dowel (20).
- Thread hollow dowel (20) into piston housing (13) until Dimension (B) is equal to
7.25 ± 0.25 mm (0.285 ± 0.010 inch) . The amount of wear indicator pin (19) that is exposed is critical to determine when the brake disc life has been exceeded.Note: Piston (22) must be fully retracted into piston housing (13) in order to set the correct hollow dowel (20) length.
Show/hide tableIllustration 12 g03692297 - Apply the lubricant that is being sealed to friction discs (11), (9), and (7).
- Install outer plate (12), friction disc (11), outer plate (10), friction disc (9), outer plate (8), friction disc (7), and outer plate (6) to spindle assembly (1).
Show/hide table
Illustration 13 g03692292 Show/hide tableIllustration 14 g03693398 - Install damper plate (5).
Note: Note the orientation on damper plate (5).
Show/hide tableIllustration 15 g03692277 - Install hub (4) into spindle assembly (1).
- Install retaining ring (3).
- Install O-ring seal (2).
Illustration 1 | g03692461 |
Illustration 2 | g03693305 |
End By:
- Install the final drive, the wheel, and the service brake piston housing.