Cab - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 140-7742 | Sleeve | 3 |
B | 318-1491 | Offset Wrench | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Attach Tooling (A) and suitable lifting devices to cab (19). The weight of cab (19) is approximately
1270 kg (2800 lb) . Use Tooling (A) and the suitable lifting devices in order to position cab (19) onto the machine.Show/hide tableIllustration 2 g03494298 - Connect harness assembly (21).
Show/hide table
Illustration 3 g03494296 - Install bolts (20). Use Tooling (B) in order to install bolts (20) that are surrounded by the fuel tanks.
Note: If you use Tooling (B), tighten bolts (20) to a torque of
548 ± 68 N·m (405 ± 50 lb ft) .Show/hide tableIllustration 4 g03494280 - Position step assembly (18) and install bolts (17). Repeat this step for the opposite side of the machine.
Show/hide table
Illustration 5 g03494237 - Install bolt (16) and harness assembly (15).
Show/hide table
Illustration 6 g03494197 - Install cover (14).
Show/hide table
Illustration 7 g01411727 - Connect harness assemblies (13) and harness assemblies (12).
Show/hide table
Illustration 8 g01411723 - Connect harness assembly (11).
Show/hide table
Illustration 9 g01411717 - Connect ground strap (10).
Show/hide table
Illustration 10 g01411519 - Position cover (9) and install bolts (8). Repeat this step for the opposite side of the machine.
Show/hide table
Illustration 11 g01411515 - Install clip (7), clip (6), and clips (5). Connect hose assemblies (4).
Show/hide table
Illustration 12 g01411507 - Connect hoses (3). Connect harness assemblies (2).
Show/hide table
Illustration 13 g01411502 - Install cover (1).
- Charge the air conditioner refrigerant into the air conditioner system. refer to Service Manual , SENR5664, "Air Conditioning and Heating Systems with R-134a for All Caterpillar Machines" for the correct procedure. Refer to Special Publication, NENG2500, "Air Conditioning Tools" for the correct tools.
Show/hide table
Illustration 1 | g03494281 |
End By:
- Separate the steering frame lock.
Caterpillar Information System:
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Control Manifold (Hydraulic Fan)
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Control Manifold (Brake)
988K XE Wheel Loader Machine Systems Steering Control Valve - Disassemble
2013/11/21 Improvement to the Boom Top Plate on Certain Backhoe Loaders {6501}
2013/10/29 New Transmission Software is Available {7610, 7620}
Procedure to Install New Blocks and Bracket Assembly for the Front Nose and Rear Valve Bank Cover on Certain 16M Motor Graders{7150} Procedure to Install New Blocks and Bracket Assembly for the Front Nose and Rear Valve Bank Cover on Certain 16M Motor Graders{7150}
2013/10/24 New Software for the Turbocharger Protection Strategy on the C4.4 Engine {1052, 1920}
2013/12/06 New Procedure to Rework the Existing Front Axle Now Available for R1600G Load Haul Dump Machines {3256, 3258, 3260}
725C Articulated Truck Declaration of Conformity
Procedure for Removing and Installing the Exhaust Cooler (NRS) on All Tier 4 C15 and C18 Engines {108C, 108G} Procedure for Removing and Installing the Exhaust Cooler (NRS) on All Tier 4 C15 and C18 Engines {108C, 108G}
730C2 EJECTOR Articulated Truck Frame and Body - Inspect
725C Articulated Truck Engine Oil and Filter - Change
14L Motor Grader Machine Systems Cab - Remove
793F Series AC Off-Highway Truck Power Train Axle Shaft - Remove and Install
2013/10/24 New Engine Software is Available for Certain 740B and 740B Ejector Articulated Trucks {1920}
2013/12/02 New Blade Mounting Group Wear Strips are Now Available On Certain 24H and 24M Motor Graders {6151}
2014/03/27 New Blade Mounting Group Wear Strips are Now Available On Certain H, K and K Series 2 Motor Graders {6152, 6154, 6155}
2013/11/22 New Blade Mounting Group Wear Strips are Now Available On Certain H, M, and M Series 2 Motor Graders {6151}
725C, 725C2, 730C and 730C2 Articulated Truck Systems General Information (Hydraulic System)
2013/11/11 The Drawbar Assembly Has Been Improved on Certain M and M Series 2 Motor Graders {6153}
2013/11/27 New Spindle for the Front Axle Group Is Used On Certain 16H and 16M Motor Graders {4205, 4313}
777G Off-Highway Truck Hydraulic and Braking System Operational Checks
226 Skid Steer Loader TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 226 Skid Steer Loader TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
2013/11/15 An Improved Centershift Lock Group Is Now Used on Certain K and K Series 2 Motor Graders {5221}