Gear Motor (Vibratory) - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tools     | Part Number     | Part Description     | Qty     |
A     | 1P-1857     | Retaining Ring Pliers     | 1     |
B     | 9S-9152     | Bearing Puller Gp     | 1     |
Start By:
- Remove the gear motor (vibratory). Refer to Disassembly and Assembly, "Gear Motor (Vibratory) - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Remove screw (5), spring (4), and ball (3) from housing (2) .
Show/hide table
Illustration 1 | g01383144 |
Show/hide table
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
- Repeat Step 1 on screw (1) .
- Mark the orientation of cover (6) and housing (2). Remove bolts (7) and carefully separate cover (6) from housing (2) .
Show/hide table
Illustration 2 | g01383145 |
- Remove driven gear (11) and drive gear (8) from cover (6) .
Show/hide table
Illustration 3 | g01383148 |
- Remove dowel pins (9) and (10) from cover (6) .
- Remove gasket (12) from cover (6). Remove bearings (13) from cover (6), if necessary.
Show/hide table
Illustration 4 | g01386175 |
- Remove woodruff key (14) from shaft (15). Use Tooling (A) to remove retaining ring (16) .
Show/hide table
Illustration 5 | g01383533 |
Show/hide table
Illustration 6 | g01383149 |
- Use a suitable press to remove shaft (15) from housing (2) .
- Remove shaft seal (19) and spacer (18) from shaft (15) .
Show/hide table
Illustration 7 | g01383151 |
- Use Tooling (B) in order to remove bearing (17) from shaft (15) .
- Remove needle bearings (20) from housing (2), if necessary.
Show/hide table
Illustration 8 | g01383153 |
Caterpillar Information System:
AccuGrade® Laser (CB420) LR 21 Check Connection
216B, 226B, 232B and 242B Skid Steer Loaders Machine Systems Accumulator (Pilot) - Test and Charge
2007/07/09 A New Spring Kit is Now Available {3065, 5063}
CS54 and CP54 Vibratory Soil Compactors Specifications
CS54 and CP54 Vibratory Soil Compactors Sound Information and Vibration Information
2007/08/06 An Improved Left Side Alternator Guard is Used {7174}
770 and 772 Off-Highway Trucks Engine Supplement Disconnect Switch (Battery) - Remove and Install
587R Pipelayer Engine Supplement Fan and Fan Drive - Remove and Install
450E Backhoe Loader Machine Systems Lift Arms - Remove
2007/06/04 An Enhanced Diagnostic Procedure is Now Available for the Air Conditioner Dryer {7322}
2007/08/06 New Water Lines Groups Are Available {1380}
Test and Repair for Excessive Current Draw{1401, 1408} Test and Repair for Excessive Current Draw{1401, 1408}
AS3301C Asphalt Screed Gear Motor (Vibratory) - Assemble
2007/07/02 A New Lift Arm Improves Reliability of Certain Backhoe Loaders {6118, 6119}
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Pilot Operated Hydraulic Control (Joystick)
3512C Engine for Caterpillar Built Machines Fuel Filter Housing - Remove - Spin-on Filter
AccuGrade® Laser (CB420) LR 1 Memory Fault
267B, 277B and 287B Multi Terrain Loaders Machine Systems Accumulator (Pilot) - Test and Charge
770 and 772 Off-Highway Trucks Engine Supplement Muffler - Remove and Install
450E Backhoe Loader Machine Systems Bank Valve (Backhoe) - Install
AccuGrade® Laser (CB420) LR 2 Memory Fault
AccuGrade® Laser (CB420) AS 2 Memory Fault
AccuGrade® Laser (CB420) AS 6 Flash Program Fault
587R Pipelayer Engine Supplement Fan Drive - Disassemble