Steering Link - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-7505     | 液压千斤顶     | 1     |
B     | 231-4903     | 楔块     | 1     |
开始:
- 安装车轮楔子。 请参阅拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
- 卸下开口销。 松开用于将球头螺柱和转向连杆 (1) 固定到位的螺母 (2) 。 此时请勿拆下螺母 (2) 。
Show/hide table
图 1 | g01320345 |
- 将工具 (B) 放置在转向接头中。 将适当的固定装置连接至工具 (B) 、润滑脂软管组件 (3) 和接头 (4) 。 用锤敲击工具 (C) ,直到球头螺柱松动。 拆下工具 (B) 和适当的固定装置。
Show/hide table
图 2 | g01320307 |
典型实例 |
- 对转向拉杆 (1) 的余下一端重复步骤 1 和 2 。
- 将工具 (A) 放置在转向拉杆 (1) 之下。 将转向拉杆 (1) 固定到工具 (A) 上,以支撑转向拉杆 (1) 的重量。 转向连杆 (1) 的重量约为 25 kg (55 lb)。
Show/hide table
图 3 | g01320541 |
典型实例 |
- 拆下螺母 (2) 。
- 从机器上拆下转向拉杆 (1) 。
- 松开卡箍 (6) ,然后拆下套筒组件 (5) 。 对转向连杆 (1) 的另一端重复该步骤。
- 从球头螺柱 (11) 上拆下密封件 (10) 。 使用螺丝刀拆卸环 (7) 和盖 (8) 。
Show/hide table
图 4 | g01320313 |
- 将球窝固定到适当的压具内。 将球头螺柱 (11) 和外座圈 (9) 压出套筒。
- 对其余球头螺柱重复步骤 8 和 9。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-7505     | 液压千斤顶     | 1     |
C     | 1P-0808     | 多功能润滑脂     | 1     |
- 使用适当的压具将球头螺柱 (11) 和外座圈 (9) 安装到套管中。 安装盖 (8) 。 使用螺丝刀将环 (7) 安装在套筒上。 将密封件 (10) 安装到不带润滑剂的球头螺柱 (11) 上。
Show/hide table
图 5 | g01320313 |
- 将工具 (C) 涂抹在球头双头螺栓 (11) 的锥形面上。
- 对转向拉杆 (1) 的另一端重复步骤1和2。
- 将套筒组件 (5) 装入转向连杆 (1) 。 将卡箍 (6) 的开口对准转向拉杆 (1) 的槽。 拧紧卡箍 (6) 。 针对其余的套筒组件重复上述步骤。
Show/hide table
图 6 | g01320541 |
典型实例 |
- 利用工具 (A) 定位转向拉杆 (1) 。 转向连杆 (1) 的重量约为 25 kg (55 lb)。
- 安装螺母 (2) 。 拧紧螺母 (2) 至扭矩为 1360 N·m (1003 lb ft)。 如果孔为对齐,将螺母 (2) 向前推导下个孔。 安装开口销。
Show/hide table
图 7 | g01320345 |
- 对转向拉杆 (1) 的另一端重复步骤 6 。
- 对准前轮。 请参阅转向系统操作、测试和调整, "前轮 - 对准"。
End By: 取走车轮楔子。 请参阅 拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Caterpillar Information System:
777E, 777F and 777G Off-Highway Truck Radiator Core - Remove
CAES Network Name Configuration
Procedure to Rework the Air Conditioning Control System{7320} Procedure to Rework the Air Conditioning Control System{7320}
2006/11/13 Improved End - of - Line - Test Fixture for the Product Link Antenna is Now Used {7606}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System Wiring Harness (Open Circuit) - Test
24M Motor Grader Implement Electronic Control System Electronic Control Module (ECM) - Flash Program
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2143 - FMI 09
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0588 - FMI 14
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0588 - FMI 09
C175-16 and C175-20 Engines for Off-Highway Trucks Starting System
AccuGrade® GPS v11 for CD700 MID 114 - CID 2291 - FMI 06
AccuGrade® GPS v11 for CD700 MID 114 - CID 2291 - FMI 05
773F and 775F Off-Highway Trucks Machine Systems Center Arm (Steering) - Remove and Install
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Rear) - Remove
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Rear) - Install
777G Off-Highway Truck Machine Systems Fuel Tank - Remove
Tightening of the Swivel Nut for the AC Dryer {7322} Tightening of the Swivel Nut for the AC Dryer {7322}
C175-16 and C175-20 Engines for Off-Highway Trucks General Information (Cooling System)
C175-16 and C175-20 Engines for Off-Highway Trucks Visual Inspection
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Front) - Remove
770 and 772 Off-Highway Truck Chassis Electronic Control System MID 087 - CID 2683 - FMI 03
770 and 772 Off-Highway Truck Chassis Electronic Control System MID 087 - CID 2683 - FMI 04
770 and 772 Off-Highway Truck Chassis Electronic Control System MID 087 - CID 2683 - FMI 08
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Front) - Install