Electronic Control Module (ECM) - Flash Program
Show/hide table
| Required Tools | |
| WinFlash Software | |
Perform the following procedures to flash program an ECM. The ECM is flashed in order to upgrade software. The ECM is flashed in order to load software into an ECM. Flash programming of an ECM must also be done if the ECM has been replaced. The Caterpillar Electronic Technician (ET) contains the program WinFlash. WinFlash is used to load software into the ECM. The following procedure is used in order to flash software into an ECM.
- Connect the 139-4166 Data Link Cable between the 7x-1700 Communication Adapter and the diagnostic connector of the machine.
- Use WinFlash to load the new software.
Note: The ECM will indicate that the ECM is "BLANK" if the ECM is blank or an unsuccessful "FLASH" was performed.
Caterpillar Information System:
3500C Marine Auxiliary Engines Factory Passwords
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2687 - FMI 08
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2687 - FMI 02
AS2302 Screed Hydraulic Cylinder (Extender Extend)
120M, 12M, 140M and 160M Motor Graders Machine Preparation for Troubleshooting
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2686 - FMI 08
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2686 - FMI 02
12M Motor Grader Cooling System Coolant Level - Check
Filtration Procedure for Hydraulic Oil in D, E, and F Series Backhoe Loaders {0680, 0768, 5050, 5056} Filtration Procedure for Hydraulic Oil in D, E, and F Series Backhoe Loaders {0680, 0768, 5050, 5056}
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2685 - FMI 08
572R Series II Pipelayer Monitoring System
12M Motor Grader Hydraulic System Oil Level - Check
773F, 773F OEM, 777F and 777F OEM Off-Highway Trucks and 775F and 775F OEM Quarry Truck Vital Information Management System (VIMS) Electronic Control Module (ECM) - Replace
773F, 773F OEM, 777F and 777F OEM Off-Highway Trucks and 775F and 775F OEM Quarry Truck Vital Information Management System (VIMS) Electronic Control Module (ECM) - Configure
140M Motor Grader Transmission and Differential Oil Level - Check
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2688 - FMI 02
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Power Train Electronic Control System
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System MID 039 - CID 2688 - FMI 08
16M Motor Grader Transmission and Differential Oil Filter and Screens - Replace/Clean
140M Motor Grader Transmission and Differential Oil - Change
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Using Advisor to Determine Diagnostic Codes
572R Series II Pipelayer Battery Disconnect Switch
140M Motor Grader Engine Oil and Filter - Change
572R Series II Pipelayer Backup Alarm