168-7440 Drive and Steering Axle Gp, with Steer Sensor
 | |
| Illustration 1 | g01174918 |
(1) Torque for 8 bolts ... 300 N·m (220 lb ft)
(2) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
(2A) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
(3) Torque for three bolts ... 190 N·m (140 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the bolts.
(4) Torque of the purging screw for the brake ... 12 N·m (106 lb in)
(4A) Torque of the purging screw for the brake ... 12 N·m (106 lb in)
(5) Torque for the plug ... 50 N·m (35 lb ft)
(5A) Torque for the plug (not shown) ... 50 N·m (35 lb ft)
(6) Torque for tie rod nut ... 280 N·m (205 lb ft)
(7) Torque for four kingpin bolts ... 250 N·m (184 lb ft)
(8) Torque for locknut ... 250 N·m (184 lb ft)
(9) Torque for the ball joint ... 300 N·m (221 lb ft)
(10) Torque for breather ... 10 N·m (90 lb in)
Install the breather so that the slot in the breather is parallel with the axle half shaft.
(11) Torque for 26 axle housing bolts ... 190 N·m (140 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the bolts.
(12) Torque for two bolts ... 60 N·m (44 lb ft)
(13) Torque for the two bolts ... 23 N·m (17 lb ft)
(14) Torque for two plugs (each carrier assembly) ... 25 N·m (20 lb ft)
(15) Torque for plug (each carrier assembly) ... 60 N·m (45 lb ft)
(16) 174-4641 Plate
- Thickness of plate ... 5.00 ± 0.05 mm (0.197 ± 0.002 inch)
(17) 217-2895 Brake Disc
- Thickness of disc ... 4.80 ± 0.05 mm (0.189 ± 0.002 inch)
- Minimum allowable thickness of disc ... 3.95 mm (0.156 inch)
208-1016 Drive and Steering Axle Gp, without Steer Sensor
 | |
| Illustration 2 | g01174939 |
(1) Torque for 8 bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the bolts.
(2) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
(2A) Torque of the locknut for the steering stop (not shown) ... 150 N·m (110 lb ft)
(3) Torque for breather ... 10 N·m (90 lb in)
Install the breather so that the slot in the breather is parallel with the axle half shaft.
Note: Apply Loctite 243 sealant to the threads prior to installing the breather.
(4) Torque for three bolts ... 190 N·m (140 lb ft)
(5) Torque of the purging screw for the brake ... 12 N·m (105 lb in)
(5A) Torque of the purging screw for the brake ... 12 N·m (105 lb in)
(6) Torque for the plug ... 50 N·m (35 lb ft)
(6A) Torque for the plug (not shown) ... 50 N·m (35 lb ft)
(7) Torque for tie rod nut ... 250 N·m (185 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the nut.
(8) Torque for four kingpin bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the bolts.
(9) Torque for locknut ... 250 N·m (185 lb ft)
(10) Torque for the ball joint ... 300 N·m (220 lb ft)
(11) Torque for thirteen axle housing bolts ... 310 N·m (230 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the bolts.
(12) Torque for the plug ... 30 N·m (22 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the plugs.
(12A) Torque for the plug (not shown) ... 30 N·m (22 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the plugs.
(13) Torque for the 30 mm (1.18 inch) plug (not shown) ... 60 N·m (45 lb ft)
(14) Torque for two plugs (each carrier assembly) ... 25 N·m (20 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the plugs.
(15) Torque for two plugs (each carrier assembly) ... 60 N·m (45 lb ft)
Note: Apply Loctite 243 sealant to the threads prior to installing the plugs.
(16) 174-4641 Plate
- Thickness of plate ... 5.00 ± 0.05 mm (0.197 ± 0.002 inch)
(17) 217-2895 Brake Disc
- Thickness of disc ... 4.80 ± 0.05 mm (0.189 ± 0.002 inch)
- Minimum allowable thickness of disc ... 3.95 mm (0.156 inch)