Engine Enclosure (Hood) - Remove and Install
Removal Procedure
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- If the machine is equipped with a cab, remove the four mounting bolts and the washers. Lift the cab and move the cab forward approximately 76 mm (3 inch). Refer to Disassembly and Assembly, "Cab - Remove and Install".
- Raise hood (1) and support with a suitable lifting device. The weight of hood (1) is approximately 105 kg (230 lb).
Show/hide table
Illustration 1 | g03188676 |
- Remove screws (3) and screen (2) .
Show/hide table
Illustration 2 | g03188702 |
- Disconnect strut (4) .
Show/hide table
Personal injury can result from parts under pressure. Stored energy force will be released when struts are removed. Support covers, hoods, or other components prior to the removal or the installation of struts. |
- Repeat Steps 3 through 4 to other side of hood (1) .
- Lower hood (1) using suitable lifting device.
- Attach a suitable lifting device to hood (1). The weight of hood (1) is approximately 105 kg (230 lb).
Show/hide table
Illustration 3 | g03188716 |
- Remove four bolts (5), the four washers, and hood (1) .
Show/hide table
Illustration 4 | g03726973 |
Installation Procedure
- Install hood (1) in the reverse order of removal.
- Tighten screws (3) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
- Place the cab into position. Install the four mounting bolts and the washers. Refer to Disassembly and Assembly, "Cab - Remove and Install".
Caterpillar Information System:
CW34 Pneumatic Compactor Engine Supplement Engine - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Electric Starting Motor - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Battery - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Alternator Belt - Remove and Install
C7.1 Industrial Engine DEF Filler Screen - Clean
CW34 Pneumatic Compactor Engine Supplement Air Cleaner - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Selector and Pressure Control Valve (Secondary Steering)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Engine and Transmission Mounting
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Valve
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Air Cleaner
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Air Cleaner - Mounting
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Steering)
CW34 Pneumatic Compactor Engine Supplement Expansion Tank - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Gear Motor (Hydraulic Fan) - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Manifold Valve (Bypass) - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Muffler - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Primary Fuel Filter, Water Separator and Base - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Refrigerant Compressor - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Support
735C and 745C Articulated Trucks Torque Converter, Transmission, and Transfer Gear Oil Filter - Replace
785G Off-Highway Truck Systems Solenoid Valve Actuator
2015/02/02 Improved Pressure Sensor Gp Is Now Used on Certain Cat® Products {1439}