Oil Pan - Remove and Install
Removal Procedure
Start By:
- Remove the engine oil level gauge. Refer to Disassembly and Assembly, "Engine Oil Level Gauge (Dipstick) - Remove and Install".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1). Loosen bolts (2) and remove panel (3) from below the engine.
Show/hide table
 | |
| Illustration 1 | g00983802 |
- Drain the engine oil into a suitable container for storage or for disposal. The capacity of the engine crankcase and filter is approximately 17.5 L (4.62 US gal).
- Cut and remove cable strap (4). Remove bolts (5) and remove oil pan (6). Remove the gasket.
Show/hide table
 | |
| Illustration 2 | g00983820 |
Installation Procedure
- Clean the mating surfaces of both the oil pan and the engine. Install a new gasket. Position oil pan (6) and install bolts (5). Install a new cable strap (4) .
Show/hide table
| | |
| Illustration 3 | g00983820 |
- Position panel (3) below the engine. Tighten bolts (2). Install bolts (1) .
Show/hide table
| | |
| Illustration 4 | g00983802 |
- Fill the engine with oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricants Viscosities and Refill Capacities".
End By: Install the engine oil level gauge. Refer to Disassembly and Assembly, "Engine Oil Level Gauge (Dipstick) - Remove and Install".
Caterpillar Information System:
320C Excavator Machine System Specifications Solenoid Valve (Quick Coupler)
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Hydraulic Accumulator (High Pressure) - Assemble
C-10, C-12, C-15 and C-16 Industrial Engines CID 0247 FMI 09 J1939 Data Link communications
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Hydraulic Accumulator (Low Pressure) - Assemble
C4.4 Industrial Engine Piston Ring Groove - Inspect
C4.4 Industrial Engine Cooling System - Inspect
304 Mini Hydraulic ExcavatorEngine Supplement and Machine Systems Engine Enclosure Group - Remove and Install
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Hydraulic Accumulator (High Pressure) - Disassemble
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Hydraulic Accumulator (Low Pressure) - Disassemble
M318C Excavator Hydraulic System Relief Valve (Medium Pressure/Cab Riser Function) - Test and Adjust
M318C Excavator Hydraulic System Flow (Medium Pressure/Cab Riser Function) - Test and Adjust
M318C Excavator Hydraulic System Flow (Medium Pressure Function) - Test and Adjust
325C Excavator 3126B Engine Supplement Engine Oil Cooler - Remove and Install
312C and 315C Excavators Tool Control System System G 1a: Relief Valve (Line) - Test and Adjust
312C and 315C Excavators Tool Control System System G 1b: Relief Valve (Line) - Test and Adjust
312C and 315C Excavators Tool Control System System G 1c: Relief Valve (Line) - Test and Adjust - One-Way System
SW45, SW60, SW80, SW345B, SW360B, SW380B, SW460B and SW480B Wheel Saws Frame Slide Bars - Lubricate
312C and 315C Excavators Tool Control System System G14: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve (Medium Pressure)
2003/04/01 New Flash File Software Is Used for Product Link 151/201 {7620}
BP24 Pickup Broom Broom Brush
BP24 Pickup Broom Broom Hitch
BP24 Pickup Broom Debris Frame
312C and 315C Excavators Tool Control System System G14: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve
312C and 315C Excavators Tool Control System System G14: Relief Valve (Main) - Test and Adjust - Auxiliary Control Valve (Medium Pressure)