Camshaft Bearings - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
8S-8293 | 伸出 | 1 | |
5P-1667 | 管 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 利用工具 (A) 安装所有凸轮轴轴承,使凸轮轴轴承内的机油孔处于水平位置。 安装角度 (1) 为 90 ± 15 度。
- 利用工具 (A) 将凸轮轴轴承安装到发动机的前端。 从每个孔的后部开始安装轴承。 利用工具 (A) 将轴承拉入孔中。 采用以下程序获得轴承的正确安装深度。
- 安装后凸轮轴轴承。 将轴承拉入孔中,直到轴承的前端面与孔 (2) 的前端面齐平为止。
- 安装窄内部凸轮轴轴承。 从发动机的尾端开始依次向前安装轴承。 将每个轴承拉入孔中,直到轴承的前端面与孔的前端面齐平为止。
Show/hide table
图 3 g00569930 测量前凸轮轴轴承的深度。 - 利用工具 (A) 将前凸轮轴轴承安装到规定的深度。 从缸体的前端测量深度。
正确安装深度的前凸轮轴轴承应当距离发动机缸体前端面
4.6 ± 0.5 mm (0.18 ± 0.02 in) 。
Show/hide table图 2 g00583232
注: 确保缸体内部清洁。 检查凸轮轴孔上有无毛刺。 安装前,在凸轮轴轴承孔内表面和每个凸轮轴轴承上涂抹薄薄的一层干净的机油。
注: 共采用两种不同的凸轮轴轴承。 将宽凸轮轴轴承安装到前后凸轮轴孔内。 将窄凸轮轴轴承安装到内孔中。
Show/hide table
图 1 | g00570127 |
注: 关于其余凸轮轴轴承安装深度的更多信息,请参阅技术参数, "凸轮轴轴承"。
结束:
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 安装"。
- 安装飞轮壳。 请参阅拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
120H Motor Grader Cutting Edges and End Bits - Inspect/Replace
216, 226 and 228 Skid Steer Loaders Engine Supplement Muffler - Remove and Install
725 and 730 Articulated Trucks Fuses - Replace
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Wheel and Tire
2006/03/27 The Differential and Bevel Gear Group Has Been Updated {3251, 3258}
140H and 160H Motor Graders Cutting Edges and End Bits - Inspect/Replace
725 and 730 Articulated Trucks Hoist, Steering, and Brake System Oil Level - Check
988G Wheel Loader Power Train Differential and Bevel Gear - Assemble
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Senders
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings - Remove
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Sensors
AP-1000B and BG-260C Asphalt Pavers Auxiliary System Shutoff Valve (Ventilation System)
797 Off-Highway Truck Power Train Transmission Hydraulic Control - Assemble
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Plate Adjustment
CB-634C Vibratory Compactor Changing Engine Speed
2000/03/20 Corrections to the Power Train Disassembly and Assembly Module, SENR1217, Power Train Disassembly and Assembly Module, SENR5976-01, Power Train Disassembly and Assembly Module, SENR5995-01, Power Train Disassembly and Assembly Module, SENR6706-01, Po
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Related Components
216, 226 and 228 Skid Steer Loaders Engine Supplement Electric Starting Motor - Remove and Install - 228 Skid Steer Loader
16H Motor Grader Cutting Edges and End Bits - Inspect/Replace
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Governor Actuator Control
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Deflector Plate Adjustment
2000/03/06 The End Of Control Cable For Implement Valve Has Serviceable Parts {5051}
2000/03/06 The VIMSpc99 Version 1.1.7 Software Update Is Now Available {7601}
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Solenoid Valves