Exhaust Inlet Nitrogen Oxide Sensor - Replace
Note: During installation and handling of the sensor, follow the parameters listed below:
- Do not expose the sensor to any fluids.
- Do not contact the sensing element when power is applied to the sensor. Contact with the sensing element may result in injury. The sensing element is heated to a minimum of
100° C (212° F) . - Do not use any lubricant on any part of the sensor other than the threads. Do not use unapproved thread lubricant. Do not apply additional anti-seize to new parts. If additional anti-seize is necessary for pre-installation, use only nickel based anti-seize or non-metallic anti-seize. Apply anti-seize to the threads only and avoid contaminating the sensor head.
- Do not use sensors that have been dropped or have been exposed to other forms of mishandling. Damage to the sensor may have occurred that is not visible.
- Replace the sensor if damaged or faulty.
To replace the NOx sensor, follow the steps listed below:
- Prepare the machine for maintenance. Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".
- Remove the covers to gain access to the sensors.
Show/hide table
Illustration 1 g06375853 - Disconnect harness assembly and disconnect sensor cabling (1).
- Remove NOx sensor probe (2).
Show/hide table
Illustration 2 g03495917 - Install inlet NOx sensor probe. Take precautions to prevent damaging the ceramic sensor element (3) when installing.
- Ensure that the sensor is securely mounted.
- Connect harness assembly and cabling.
Note: Ensure that the NOx sensor is not covered with insulation. The insulation would trap heat in the sensor body and cable. This heat may cause sensor failure.
- Install cover plate assemblies and bolts. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque.
Caterpillar Information System:
794 AC Off-Highway Truck Breather Line (Diesel Exhaust Fluid) - Inspect
C27 and C32 Generator Set Engines Atmospheric Pressure Sensor - Remove and Install
794 AC Off-Highway Truck Breather (DEF Tank) - Replace
C175 Tier 4 Final Engines for Caterpillar Built Machines Water Pump - Remove and Install
794 AC Off-Highway Truck Screen (DEF Coolant) - Clean
A Procedure to Improve the Tail Box Section of the (HP) Body for 797F Off-Highway Trucks is Available {7250, 7258, 7269, 7583} A Procedure to Improve the Tail Box Section of the (HP) Body for 797F Off-Highway Trucks is Available {7250, 7258, 7269, 7583}
120 and 120 AWD Motor Grader Fuel System Filter (In-Line) - Replace
120 and 120 AWD Motor Grader Fuel System Filter - Replace
120 Motor Grader Monitoring System Display Navigation
120 and 120 AWD Motor Grader Open Crankcase Ventilation (OCV) Fumes Disposal Filter - Replace
120 and 120 AWD Motor Grader Fuel System - Prime
Previous Rear Door Seal Removed On Certain XQ125 Generator Sets {7274} Previous Rear Door Seal Removed On Certain XQ125 Generator Sets {7274}
794 AC Off-Highway Truck Exhaust Outlet Nitrogen Oxide Sensor - Replace
794 AC Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New
120 and 120 AWD Motor Grader Transmission and Differential Oil Filter and Screens - Replace/Clean
120 and 120 AWD Motor Grader Transmission and Differential Oil Level - Check
120 and 120 AWD Motor Grader Belts - Inspect/Adjust/Replace
XQ570 Rental Generator Set Setup
120 and 120 AWD Motor Grader Transmission and Differential Oil Sample - Obtain
C27 and C32 Generator Set Engines Crankshaft Position Sensor - Remove and Install
120 and 120 AWD Motor Grader Fuel System Water Separator - Drain
336, and 340 Excavator TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} 336, and 340 Excavator TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}
120 and 120 AWD Motor Grader Declaration of Conformity
120 Motor Grader Monitoring System Display Module