Exhaust - Install
Parts and Specification Information
Show/hide table
Illustration 1 | g03850916 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
Show/hide table
Personal injury or death can occur from heavy components falling during removal or installation. Properly support the component with a suitable lifting device during removal or installation. |
Show/hide table
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information. |
Show/hide table
Item | Part Number | Description | Qty | Specification | Approximate Weight |
1 | 242-0799 | Bellows As | 2 | ||
2 | 302-8136 | Band Clamp | 4 | ||
3 | 6V-2673 | Protection Cap | 4 | ||
4 | 444-8842 | Exhaust Pipe | 2 | ||
5 | 444-8840 | Exhaust Pipe | 1 | |
|
6 | 444-8841 | Exhaust Pipe | 1 | |
|
7 | 432-8099 | Bracket | 8 | ||
8 | 4L-9337 | Bolt | 22 | ||
9 | 6V-8801 | Nut | 20 | ||
10 | 445-9753 | Support Bracket | 1 | ||
11 | 5P-1075 | Hard Washer | 8 | ||
12 | 431-5837 | Clamp As | 2 | ||
13 | 444-8831 | Connector Rod | 4 | ||
14 | 8T-2501 | Bolt | 10 | ||
15 | 8T-4896 | Hard Washer | 12 | ||
16 | 054-4984 | Spacer | 8 | ||
17 | 7V-0574 | Rod End | 4 | ||
18 | 4V-5487 | Rod End | 4 | ||
19 | 6V-8183 | Full Nut | 4 | ||
20 | 444-8839 | Exhaust Pipe As | 1 | |
|
21 | 444-8838 | Exhaust Pipe As | 1 | |
|
22 | 444-8822 | Bracket As | 1 | ||
23 | 7X-0346 | Bolt | 3 | ||
24 | 7X-0515 | Hard Washer | 6 | ||
25 | 7X-0448 | Nut | 3 | ||
26 | 444-8832 | Hanger | 1 | ||
27 | 444-8833 | Hanger | 1 | ||
28 | 444-8825 | Tube Support | 4 | ||
29 | 444-8843 | Exhaust Blanket | 2 | ||
30 | 444-8845 | Exhaust Blanket | 1 | ||
31 | 444-8847 | Exhaust Blanket | 1 | ||
32 | 444-8844 | Exhaust Blanket | 1 | ||
33 | 444-8846 | Exhaust Blanket | 1 | ||
34 | 444-8848 | Exhaust Blanket | 2 | ||
35 | 251-6357 | Heat Shield | 2 |
- Install one bellows assembly (1) to each of the two exhaust manifolds. Secure the bellows assembly (1) in place using one band clamp (2). Install one protection cap (3) on the end of the threads of each band clamp (2).
- Install one exhaust pipe (4). on the end of each bellows assembly (1). Secure the exhaust pipe (4) in place using one band clamp (2). Install one protection cap (3) on the end of the threads of each band clamp (2).
Show/hide table
Illustration 3 g03851370 A view of the rear of the engine Show/hide tableIllustration 4 g03851608 Close up view of the connector rod - Install exhaust pipe (5) and exhaust pipe (6), each to an exhaust pipe (4).
- Install four brackets (7) and secure each pair with four bolts (8) and four nuts (9).
- Install support bracket (10) with four bolts (8) and four hard washers (11). Secure exhaust pipe (5) and exhaust pipe (6) to exhaust pipes (4).
- Secure exhaust pipe (5) and exhaust pipe (6) in place. Secure each with one clamp assembly (12). Connect each clamp assembly (12) to support bracket (10) using two connector rods (13). Install each connector rod to clamp assemblies (12) using one bolt (14), one hard washer (15), one spacer (16), one rod end (17), and one nut (9). Install each connector rod to support bracket (10) using one bolt (14), two hard washers (15), one spacer (16), one rod end (18), and one nut (9).
- Install a full nut (19) on each connector rod (13) to adjust the height of the rod.
Show/hide table
Illustration 5 g03851685 A view of the rear of the engine - Install exhaust pipe assembly (20) and exhaust pipe assembly (21). Secure each to the preceding exhaust pipe using four brackets (7) eight bolts (8), and eight nuts (9).
Show/hide table
Illustration 6 g03852012 A view of the rear of the engine - Once all exhaust lines are positioned correctly, install bracket assembly (22) to the platform assembly using three bolts (23), six hard washers (24), and three nuts (25).
- Install hanger (26) and hanger (27) to bracket assembly (22) using one bolt (8), two hard washers (11), and one nut (9) at the top of each hanger.
- Install two tube supports (28) around each exhaust pipe and secure each to the bottom of a hanger using two bolts (14) and two nuts (9) on each pair of tube supports (28).
Show/hide table
Illustration 7 g03852181 A view of the rear of the engine - Install one exhaust blanket (29) on each exhaust line.
- Install exhaust blanket (30) and exhaust blanket (31) on the lower exhaust line.
- Install exhaust blanket (32) and exhaust blanket (33) on the upper exhaust line.
- Install one exhaust blanket (34) and one heat shield (35) on each exhaust line.
Show/hide table
Illustration 2 | g03851253 |
A view of the top of the engine |
Caterpillar Information System:
Rebuild Instructions for the High Temperature Throttle Used on Certain G3500C and G3500E Engines {1269} Rebuild Instructions for the High Temperature Throttle Used on Certain G3500C and G3500E Engines {1269}
3512C Generator Set Engine Accessory Drive (Front) - Remove and Install
A New Gas Shutoff Valve Is Available For Certain G3306 and G3306B Engines {1259, 1704} A New Gas Shutoff Valve Is Available For Certain G3306 and G3306B Engines {1259, 1704}
C27 and C32 Industrial Engines Maintenance Interval Schedule
C8.7 Marine Engine Inlet and Exhaust Valves - Remove and Install
False Intake Manifold Air Temperature Causing Shutdown on Certain G3412 Engines with EMCP 4.2 Panels{1920, 4490, 7490} False Intake Manifold Air Temperature Causing Shutdown on Certain G3412 Engines with EMCP 4.2 Panels{1920, 4490, 7490}
2015/06/26 New Software Is Now used on Certain C11 Engines {7620}
2015/07/07 A New Liner Seal Is Used on Certain G3300 Engines {1201}
2015/07/07 Timer Rework for Overhead Lights in XQ2000 {1429}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
330F MHPU Mobile Hydraulic Power Unit Track Adjustment - Adjust - If Equipped
3512C Generator Set Engine Valve Mechanism Cover Base - Remove and Install
C4.4 and C7.1 Engines Service Tool Features
C27 and C32 Industrial Engines Product Description
C27 and C32 Industrial Engines Refill Capacities
C4.4 and C7.1 Engines Service Tool Error Identifiers
C27 and C32 Industrial Engines Overhaul Considerations
C280-08 Tier 4 Engine Engine Oil Coolers - Remove and Install
CG137-08 and CG137-12 Engines Sound Information
CG137-08 and CG137-12 Engines Model View Illustrations
C280-08 Tier 4 Engine Engine Oil Coolers - Disassemble
C8.7 Marine Engine Camshaft Bearings - Remove and Install
CG137-08 and CG137-12 Engines Product Description
CG137-08 and CG137-12 Engines Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.4