G3500 A3 Engines Caterpillar

Camshaft

Usage:

G3516 N6A

Show/hide table




Illustration 1	g03126416
(1) Left-hand camshaft assembly (2) Right-hand camshaft assembly

Show/hide table

Table 1
Specification for 382-5086 Camshaft Gp
Item	Qty	Part	Specification Description
A	-	-	Thickness of the groove in a new camshaft assembly is 8.75 ± 0.05 mm (0.344 ± 0.002 inch).
C	1	5B-5821 Dowel	Extension of the dowel is 12.0 ± 0.5 mm (0.47 ± 0.02 inch).
D	2	4N-1650 Dowel	Extension of the dowel is 22.0 ± 0.5 mm (0.87 ± 0.02 inch).
E	2	7N-3218 Thrust Washer	Thickness of a new thrust washer is 8.50 ± 0.05 mm (0.335 ± 0.002 inch).
F	-	-	Diameter of bearing journal in a new camshaft assembly is 85.88 ± 0.02 mm (3.381 ± 0.001 inch).
F	-	-	Bore in camshaft bearing after installation is 86.00 ± 0.06 mm (3.386 ± 0.002 inch).
3	16	5P-0076 Bolt	Torque to 55 ± 7 N·m (41 ± 5 lb ft).

Show/hide table




Illustration 2	g03126417

Show/hide table

Table 2
Item	Qty	Part	Specification Description
-	-	-	Use the following procedure in order to determine the camshaft lobe lift:
			1. Measure camshaft lobe height (H).
			2. Measure base circle (J).
			3. Subtract the base circle (J) from the camshaft lobe height (H). The difference is the actual camshaft lobe lift.
G	-	-	Specified camshaft lobe lift:
			Inlet lobe is 6.499 mm (0.2559 inch).
			Exhaust lobe is 8.699 mm (0.3425 inch).

Caterpillar Information System:

G3500B Engines Turbocharger

G3500 A3 Engines Turbocharger

C13 Tier 4 Final Engines Exhaust Lines

G3512H and G3516H Generator Set Engines Housing (Front) - Remove and Install

G3512H and G3516H Generator Set Engines Engine Oil Pump - Remove and Install

G3512H and G3516H Generator Set Engines Prelubrication Oil Pump - Remove and Install

G3512H and G3516H Generator Set Engines Crankshaft - Remove and Install

2013/04/25 Clarification Of The Service Interval For The Connecting Rod Bearings For Certain C175-16 Marine Engines {1219}

3500 Engines Exhaust Elbow

Bench Test Procedure for a CX48-P2300 Transmission {0599, 0717, 3003, 3030, 3101, 3159} Bench Test Procedure for a CX48-P2300 Transmission {0599, 0717, 3003, 3030, 3101, 3159}

G3512H and G3516H Generator Set Engines Camshaft - Remove and Install

3512B and 3512C Petroleum Generator Set Engines Air Cleaner

C13, C15, and C18 Tier 4 Final Engines Diesel Particulate Filter

G3500 A3 Engines Prelube Pump

G3500 A3 Engines Balancer Group (Front)

G3500B Engines Exhaust Manifold

G3516 Engines Flywheel

C175-16 Locomotive Engine Electronic Control Module (ECM)

C175-16 Locomotive Engine Fuel System Operation

C175-16 Locomotive Engine Lubrication System Operation

G3500 Engines Flywheel

C175-16 Locomotive Engine Finding the Top Center Position for the No. 1 Piston

G3500J Petroleum Engines Flywheel Housing Cover

C3.3 and C4.4 Generator Sets Valve Mechanism Cover - Remove and Install - Three Cylinder Engines