Gear Group (Front)
Show/hide table
| Injection timing | ||
| Engine | Maximum rated engine speed | Injection timing (BTDC)(1) |
| C1.5 (Turbocharged) | 2400 | 16° ± 1° |
| C1.5 (Turbocharged) | 2800 | 16° ± 1° |
| C1.5 (Turbocharged) | 3000 | 16° ± 1° |
| C2.2 (Naturally Aspirated) | 1800 | 14.5° ± 1° |
| C2.2 (Naturally Aspirated) | 2400 | 18° ± 1° |
| C2.2 (Naturally Aspirated) | 2600 | 17° ± 1° |
| C2.2 (Naturally Aspirated) | 2800 | 17° ± 1° |
| C2.2 (Naturally Aspirated) | 3000 | 18° ± 1° |
| C2.2 (Turbocharged) | 1800 | 15° ± 1° |
| C2.2 (Turbocharged) | 2600 | 18° ± 1° |
| C2.2 (Turbocharged) | 2800 | 19° ± 1° |
| C2.2 (Turbocharged) | 3000 | 20° ± 1° |
Show/hide table
| (1) | Before Top Dead Center |
Show/hide table
| |
| Illustration 1 | g01335525 |
|
Typical example | |
(1) Feeler gauge
(2) Timing mark on the crankshaft gear
(3) Timing mark on the camshaft gear
(4) Timing mark on the idler gear
Minimum backlash for all gears ...
Maximum backlash for all gears ...
Note: If the backlash is greater than the maximum backlash, replace the camshaft gear, the idler gear, and the crankshaft gear.
When the idler gear is installed on the shaft of the oil pump, align a timing mark on idler gear (4) with the timing mark on crankshaft gear (2). Also, align the other timing mark on idler gear (4) with the timing mark on camshaft gear (3).
Caterpillar Information System:
C18 Marine Auxiliary and Marine Generator Set Engines Cooling System
Set up Procedure for the Low-Pressure Fuel System of 3600 and C280 Diesel Engines{1250} Set up Procedure for the Low-Pressure Fuel System of 3600 and C280 Diesel Engines{1250}
Failure of Digital Communication Unit (DCU) Crank Output on Certain Cat® Engines{7451} Failure of Digital Communication Unit (DCU) Crank Output on Certain Cat® Engines{7451}
O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555} O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555}
C175-16 Locomotive Engine Inlet Manifold
C175-16 Locomotive Engine Component Location
C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve
C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Head Valves
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Head
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Block
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Nozzles
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump
C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch
C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator and Regulator
C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Electronic Service Tool Does Not Communicate
C280 Marine and Petroleum Engines Electrical Power Supply - Test
C280 Marine and Petroleum Engines Solenoid Valve - Test
Cat® Command for Hauling - 793F CMD Onboard Autonomy Setup and Configuration Guide {7605, 7610, 7620} Cat® Command for Hauling - 793F CMD Onboard Autonomy Setup and Configuration Guide {7605, 7610, 7620}
C1.5 and C2.2 Engines for Caterpillar Built Machines Coolant Temperature Sensor
3516B Engine for the MT4400D Off-Highway Truck Air Lines - Aftercooler