A New Seal Improves Starter Durability on Certain Industrial Engines {1453, 7555}
- Engine:
- C7 (S/N: JTF1-UP)
- Industrial Engine:
- C13 INDUSTRIAL (S/N: RRA1-UP; LGK1-UP)
- C15 IND (S/N: JRE1-UP; MCW1-UP)
- C18 INDUSTRIAL (S/N: WJH1-UP; WRH1-UP)
- C9 INDUSTRIAL (S/N: JSC1-UP; MBD1-UP)
The most common industrial applications are in rock crushers and wood chippers. This seal is available for all products that use the 237-1962 Electric Starting Motor Gp, except for wet sump flywheel housings. The seal will stop dust accumulation on the armature spline that could prevent the pinion drive assembly from translating during normal operation.
The new 419-7866 Starter Seal is adaptable back to the first production of the listed engines.
If the starting motor on an above listed engine exhibits symptoms like, click-no-crank, running engaged and a shorted or open circuit, make the following improvement.
Seal Mounting Procedure
- Disassemble the nose cone from the starter by removing the flange bolts (1) .
Show/hide table
Illustration 1 | g03407826 |
- Install a 419-7866 Starter Seal (2) over the drive assembly until the seal rests on the ledge inside the shift lever housing. Ensure that the flat surface of the seal, identified by the gold color near the outside diameter, is facing the pinion side of the starter.
Show/hide table
Illustration 2 | g03407815 |
- Reassemble the nose cone onto the starter and torque the flange bolts to 23 ± 3 N·m (17 ± 2 lb ft).
Caterpillar Information System:
C175-16 Locomotive Engine Configuration Parameters
C175-16 Locomotive Engine Electrical Connectors
C27 and C32 Industrial Engines and C32 Petroleum Engine Refill Capacities
3516B Engine Air Conditioner Compressor - Remove and Install
Retrofitting for the Dynamic Gas Blending Capability on Certain 3512B Engines{1250, 1280} Retrofitting for the Dynamic Gas Blending Capability on Certain 3512B Engines{1250, 1280}
3516B Engine Water Temperature Regulators - Install
Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain C175-16 Generator Sets{1050, 1091} Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain C175-16 Generator Sets{1050, 1091}
421-9726 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000} 421-9726 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000}
C27 and C32 Industrial Engines Coolant (ELC) - Change
C175-16 Marine Engine Generator Coupling
TA2 Inspection for C175-16 and C175-20 Engines{1000} TA2 Inspection for C175-16 and C175-20 Engines{1000}
2012/12/21 New Sequence for Adjusting the Fuel Injectors in 3516, 3516B, and 3516C Engines {1290}
C175-16 Locomotive Engine Flywheel Housing Cover
G3500 Engines Air Starting Motor
C175-16 Marine Engine Junction Box
C175-16 Locomotive Engine Engine Oil Lines
C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft
C175-16 Locomotive Engine Water Lines
C27 and C32 Generator Sets Coolant Sample (Level 1) - Obtain
C175-16 Locomotive Engine Electrical Power Supply - Test
C27 and C32 Industrial Engines Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C18 Marine Auxiliary and Marine Generator Set Engines Engine Valve Lash - Inspect/Adjust
2013/01/10 TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
2012/12/21 A New Piston, Piston Rings, and Cylinder Liner Are Used with Certain G3516E and G3520E Engines {1201, 1214, 1215, 1216}