New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
- Engine:
- G3508 (S/N: 4WD1-UP; 9TG1-UP)
- Petroleum Engine:
- G3520B (S/N: TPC1-UP)
- Power Module:
- PMG3516 (S/N: CFD1-UP)
- G3508 (S/N: CPJ1-UP)
- G3508 (S/N: 2TJ1-UP; WPM1-UP; WPN1-UP; DLR1-UP)
- G3508 (S/N: CPS1-UP; CPY1-UP)
- G3508B (S/N: RBK1-UP)
- G3512 (S/N: 5JD1-UP; 7NJ1-UP)
- G3512 (S/N: CRN1-UP; CSP1-UP)
- G3512 (S/N: WPP1-UP; WPR1-UP; GNS1-UP)
- G3512B (S/N: JHH1-UP)
- G3516 (S/N: ZBA1-UP; 8LD1-UP)
- G3516 (S/N: CPG1-UP)
- G3516 (S/N: 4EK1-UP; WPS1-UP; WPT1-UP; WPW1-UP)
- G3516 (S/N: CSZ1-UP)
- G3516 (S/N: ZAZ1-UP)
- G3516B (S/N: ZBB1-UP)
- G3516B (S/N: CSC1-UP)
- G3516B (S/N: ZBC1-UP)
- G3516B (S/N: CME1-UP)
- G3516B (S/N: JEF1-UP; CEY1-UP; 7EZ1-UP)
- G3520B (S/N: CWD1-UP)
- G3520B (S/N: GLF1-UP; GZP1-UP)
- G3520B (S/N: GET1-UP; BGW1-UP)
Description of Change: The manufacturing process for the new exhaust valves provides a longer service life than the former valve.
The former exhaust valve was replaced by two different valves. One of the new valves is for non-landfill applications and the other new valve is for landfill applications.
Adaptable To: The new exhaust valves and the former exhaust valve are listed in Table 1. The former exhaust valve is canceled.
Note: Make sure to use the correct exhaust valve for the application.
Show/hide table
New Exhaust Valve for Non-Landfill Applications     | New Exhaust Valve for Landfill Applications     | Former Exhaust Valve     |
307-4641 Exhaust Valve     | 308-9177 Exhaust Valve     | 104-7184 Valve     |
The new exhaust valves are effective with engines built beginning 11May 2012.
Caterpillar Information System:
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
G3520E Generator Set Engines Cylinder Block
C32 Marine Engines Heat Exchanger - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Remove and Install
C175-16 Generator Set Engine Engine Oil Filter Housing - Remove and Install
C175-16 Generator Set Engine Engine Oil Pump - Assemble
2012/11/09 A New Canadian Standards Association (CSA) Ignition Harness Is Used by Certain G3406 Engines {1408}
2012/10/04 A New Unit Injector Wiring Group Is Used on Certain C9.3 Industrial Engines {1290, 1408, 1900}
C175-16 Generator Set Engine Engine Oil Pump - Disassemble
C175-16 Generator Set Engine Engine Oil Pump - Remove and Install
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
G3520E Generator Set Engines Water Lines
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Assemble
C175-16 Generator Set Engine Engine Oil Screen - Remove and Install
C175-16 Generator Set Engine Engine Oil Pan - Remove and Install
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Worksheet
2012/10/30 A New Pressure Relief Valve for the Fuel Rail Group Is Used in Certain C9.3 Industrial Engines {1288}
2012/10/11 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
2012/10/15 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
C13, C15, and C18 Tier 4 Final Engines DEF Control Module Power - Test