Engine Oil Pan - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7498 | Support Stand As | 4 |
1U-7501 | Extension Tube | 4 | |
B | 138-7573 | Link Bracket | 3 |
C | 323-1146 | Engine Lifting Device | 1 |
- Turn the battery disconnect switch to the OFF position.
- Turn the fuel supply valve to the OFF position.
Show/hide table
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.
Dispose of all fluids according to local regulations and mandates.
- Drain the oil from the engine into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
Show/hide table
Illustration 1 g01214538 - Remove bolts (2) and bolts (3). Remove elbow (4) from engine oil pump (1).
Show/hide table
Illustration 2 g01559073 - Disconnect hose assemblies (5) and (6) from fuel filter housing (7).
Show/hide table
Illustration 3 g01559133 - Disconnect hose assemblies (8), (9), and (10).
Show/hide table
Illustration 4 g01559113 - Disconnect harness assemblies (11) and (12).
Show/hide table
Illustration 5 g03277457 - Remove bolts (13) and (14).
Show/hide table
Illustration 6 g01559153 - Attach Tooling (C) onto the engine. The weight of the engine is approximately
10343 kg (22802 lb) . Remove bolts (14) on all sides of engine oil pan (15).Show/hide tableIllustration 7 g01559173 - Raise the engine from engine oil pan (15).
Show/hide table
Illustration 8 g01559193 - Position the engine on Tooling (A).
Show/hide table
Illustration 9 g01559213 - Attach Tooling (B) and a suitable lifting device onto engine oil pan (15). The weight of engine oil pan (15) is approximately
567 kg (1250 lb) . Apply slight lifting tension on engine oil pan (15). Reach through the holes in platform (16) in order to remove bolts (17). Remove engine oil pan (15) from platform (16).
- Install engine oil pan (15) in the reverse order of removal.
Caterpillar Information System:
C175-16 Generator Set Engine Engine Oil Screen - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Assemble
G3520E Generator Set Engines Water Lines
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
G3520E Generator Set Engines Cylinder Block
C32 Marine Engines Heat Exchanger - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Worksheet
2012/10/30 A New Pressure Relief Valve for the Fuel Rail Group Is Used in Certain C9.3 Industrial Engines {1288}
2012/10/11 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
2012/10/15 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
C13, C15, and C18 Tier 4 Final Engines DEF Control Module Power - Test
C13, C15, and C18 Tier 4 Final Engines NOx Conversion Is Low
C13, C15, and C18 Tier 4 Final Engines SCR Catalyst Inlet Temperature Sensor - Test
3500 Generator Sets with Dynamic Gas Blending Fluid Recommendations
2012/10/08 An Improved Hand Operated Fuel Priming Pump Is Available {1258}
3500 Generator Sets with Dynamic Gas Blending Starting the Engine - Natural Gas
2012/10/08 An Improved Hand Operated Fuel Priming Pump Is Available {1258}
C32 Marine Engines Electric Starting Motor - Remove and Install